background image

–– Contents ––

1. 

LonWorks Interface Overview 

2

Product Overview
System Diagram
Functions

2. 

Installation Instructions of LonWorks Interface 

4

Safety Precautions
Included Parts
Installation Method
Wiring Specifi cations
LonWorks Interface Structure
Power Board Initial Settings 

5

Power Board Wiring
Wiring Procedure
Main Circuit Board
Indoor Unit Enabling Switches 

6

Setting Switches
Address Switches
Communications LED (Green) 

7

Data LED (Red)
Diagram of External Dimensions
Product Specifi cations

3. 

Assigning Central Control Addresses 

8

4. 

LonWorks Interface Test Run 

9

5. 

Checking the LonWorks Interface Version 

10

6. 

List of LonWorks Network Variables 

11

7. 

Details of LonWorks Network Variables 

12

8. 

Locations Where Neuron ID is Applied 

15

Note:

   This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

   FCC Caution: To assure continued compliance, follow the attached installation instructions. 

Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to 
operate this equipment.

LonWorks is a registered trademark of the Echelon Corporation.

85464369526011

INSTALLATION INSTRUCTIONS

LonWorks Interface
Model No. CZ-CLNC1U

Pana̲CZ-CLNC1U̲Eng.indd   1

Pana̲CZ-CLNC1U̲Eng.indd   1

2011/11/11   12:23:41

2011/11/11   12:23:41

Содержание CZ-CLNC1U

















Отзывы: