manualshive.com logo in svg

Panasonic CU-2E15LBE, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CU-2E15LBE Скачать руководство пользователя страница 60

60

17.2. Self Diagnosis Function (CU-3E18LBE and CU-4E23LBE)

• The display screen of wireless remote control unit and the self-diagnosis LEDs (green) on the outdoor printed circuit board in the

outdoor unit can be used to identify the location of the problem.
Refer to the table below to identify and solve the cause of the problem, and then re-start the air conditioner system.

• If the problem is solved and operation returns to normal.

LED 1 illuminates and others LED are off.

LED  6 LED  5 LED  4 LED  3 LED  2 LED  1

Abnormality

judgement

Protection

operation

Problem

Check location

Diagnosis

display

Abnormality 

or

protection 

control

H11

Indoor/outdoor 
abnormal 
communication

After 
operation for 
1 minute

Indoor fan only 
operation can 
start by 
entering into 
force cooling 
operation

Indoor/outdoor 
communication not 
establish

• Indoor/outdoor 

wire terminal

• Indoor/outdoor 

PCB

• Indoor/outdoor 

connection wire

H12

Indoor unit 
capacity 
unmatched

90s after 
power supply

—

Total indoor 
capability more than 
maximum limit or 
less than minimum 
limit, or number of 
indoor unit less than 
two.

• Indoor/outdoor 

connection wire

• Indoor/outdoor 

PCB

• Specification and 

combination table 
in catalogue

H15

Compressor 
temperature 
sensor 
abnormality

Continuous 
for 5s

—

Compressor 
temperature sensor 
open or short circuit

• Compressor 

temperature 
sensor lead wire 
and connector

H16

Outdoor 
current 
transformer 
(CT) 
abnormality

—

—

Current transformer 
faulty or compressor 
faulty

• Outdoor PCB 

faulty or 
compressor 
faulty

H27

Outdoor air 
temperature 
sensor 
abnormality

Continuous 
for 5s

—

Outdoor air 
temperature sensor 
open or short circuit

• Outdoor air 

temperature 
sensor lead wire 
and connector

H28

Outdoor heat 
exchanger 
temperature 
sensor 1 
abnormality

Continuous 
for 5s

—

Outdoor heat 
exchanger 
temperature sensor 1 
open or short circuit

• Outdoor heat 

exchanger
temperature 
sensor 1 lead 
wire and 
connector

H32

Outdoor heat 
exchanger 
temperature 
sensor 2 
abnormality

Continuous 
for 5s

—

Outdoor heat 
exchanger 
temperature sensor 2 
open or short circuit

• Outdoor heat 

exchanger
temperature 
sensor 2 lead 
wire and 
connector

H33

Indoor / 
outdoor 
misconnection
abnormality

—

—

Indoor and outdoor 
rated voltage 
different

• Indoor and 

outdoor units 
check

H36

Outdoor gas 
pipe
temperature 
sensor 
abnormality

Continuous 
for 5s

Heating 
protection 
operation only

Outdoor gas pipe 
temperature sensor 
open or short circuit

• Outdoor gas pipe 

temperature 
sensor lead wire 
and connector

H37

Outdoor liquid 
pipe
temperature 
sensor 
abnormality

Continuous 
for 5s

Cooling 
protection 
operation only

Outdoor liquid pipe 
temperature sensor 
open or short circuit

• Outdoor  liquid 

pipe temperature 
sensor lead wire 
and connector

Содержание CU-2E15LBE








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды