background image

chassis. Connect the test equipment to the proper ground(hot) or 
(cold) when servicing, or incorrect voltages will be measured.

2.1. X-Ray Protection Circuit Check& Adjustments

This test must be performed as final check before the receiver is returned to the customer. If 
voltages are out of tolerance, immediate service and correction is required to insure safe 
operation and to prevent the possibility of premature componentfailure.

Equipment:

1. Isolation transformer.

2. High voltage meter.

3. D.C. Ammeter

4. Short jumper.

5. HHS jig (See figure below).

Diode Connection Jumper.

Preparation:

1. Make sure the receiver is turned off.

2. Connect the receiver to an isolation transformer.

3. Connect the ammeter serial from the flyback anode lead to the 

picture tube anode socket.

4. Prepare short jumper and HHS jig.

Procedure:

1. Connect the short jumper between TPD16 & TPD17.

2. Connect the jumper diode between TPD14 and TPD15 (anode 

connected to TPD15 and cathode to TPD14).

3. Apply 75VAC to AC input of isolation transformer.

4. Turn the receiver on.

7

MC-Service

Содержание CT27E13G - 27" COLOR TV
































































































Отзывы: