background image

4.1.1. +B Voltage

Item / preparation

 1. Operate the TV set.

 2. Set control as follows :

Brightness ........... minimum

Contrast ............... minimum

Adjustment procedure

 1. Confirm the DC voltage at the indicated test points, as

follows :

TPD 15 : 3.35 ± 0.2V

TPD 16 : 141 ± 2V

TPD 17 : 8.2 ± 0.5V

TPD 18 : 1.9 ± 0.2V

TPD 19 : 5.2 ± 0.2V

TPD 20 : 175 ± 15V

4.1.2. High Voltage

Item / preparation

 1. Receive the crosshatch pattern.

 2. Set to 0 Beam.

Screen VR .......... minimum

Contrast .............. minimum

Adjustment procedure

 1. Connect a DC voltage meter to D866 and confirm the +B

voltage is 141.0 ± 2V.

 2. Connect a high frequency voltmeter to heater and confirm

that voltage reads 6.30 ± 0.24 (VRMS).

 3. Normalize the brightness and contrast.

 1. Set Bright and Contrast controls to their maximum

positions.

 2. Operate the TV set over 60 minutes.

 3. Full degauss the picture tube by using an external

degaussing coil. By rotating R-B static convergence
magnet.

 4. Apply a crosshatch pattern signal and adjust roughly the

static convergence magnets.

 5. Apply a green pattern signal.

 6. Loosen a clamp screw for the Deflection Yoke and move

the Deflection Yoke as close to the purity magnet as
possible.

 7. Adjust the purity magnet so that a vertical green field is

obtained at the center of the screen.

4.1.3. NTSC TINT COLOUR

Item / preparation

 1. Connect oscilloscope probe to TPL1 (R OUT) with 10k

series resistor.

 2. Press Main Menu and set system to use AV-NTSC (3.58

MHz).

DYNAMIC ................... Normal

Channel CLR Set ..... STD

Adjustment procedure

 1. Adjust Sub-Tint so that No. 2, 3 and 4 becomes level

waveform is similar to Fig. 3.

 2. Confirm phase at Tint is changes more than ± 15 by Tint

control.

 3. Confirm that colour level is maximum when colour DAC is

adjusted to maximum position.

Note:

Use remote control only when adjusting user mode to

Sub-Tint.

 8. Slowly press the Deflection Yoke and set it where a uniform

green field is obtained.

 9. Adjust roughly the Low Light controls and make sure that a

uniform white field is obtained.

 10. Tighten the clamp screw.

4 Adjustment Procedure

4.1. Adjustment Procedure

4.2. COLOUR PURITY

7

CT-F2156WLP

Содержание CT-F2156WLP
































Отзывы: