Panasonic CT-13R32CE Скачать руководство пользователя страница 15

Страница: 15 / 51

- 15 -

Press the POWER Button on the Remote Control to select the Service Adjustment.

For Adjustments:

Sub-Data Adjustment

Default

Level

SUB-COLOR

SUB-TINT

SUB-BRIGHTNESS

127

SUB-CONTRAST

R OFFSET-factory preset

YNR-factory preset

YNR LIM-factory preset

Cut-Off Adjustment

Default

Level

CUT-OFF R

0 255

CUT-OFF G

0 255

CUT-OFF B

0 255

R DRIVE

G DRIVE

B DRIVE

V-SIZE

127

NOT USED

H CENTER

ACL

HHS

OSD SHIFT-factory preset

ACL-REF-factory preset

C10

ACL-REF-factory preset

C11

ACL-REF-factory preset

C12

ACL-REF-factory preset

C13

ACL-COEF-factory preset

124

C14

ACL-COEF-factory preset

117

1.Press Channel Up/Down on the

Remote Control to select one of
the available Service Adjustments
(a in Fig. 14).

Note: Write Down the original

value set (b in

Fig. 14

) for

each address before
modifying anything. It is
easy to erroneously adjust
the wrong item.

2.Press Volume Up/Down on the

Remote Control to adjust the
level of the selected Service
Adjustment (b in Fig. 14).

Note: Registers noted

with “factory
preset” should
not be modified.

Содержание CT-13R32CE




















































Результаты поиска

Содержание CT-13R32CE

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CT-13R32CE, Руководство по обслуживанию

Результаты поиска

Содержание CT-13R32CE

Отзывы:

Бренды по названию

Популярные бренды