manualshive.com logo in svg

Panasonic CT-13R32CE, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CT-13R32CE Скачать руководство пользователя страница 1

The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this Manual.

Service Manual

Color Television

(NA7D)

Main Manual

Copyright 2001 by Matsushita Electric Corporation of
America. All rights reserved. Unauthorized copying
and distribution is a violation of law.

“WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death.” 

ORDER NO. MTNC010412C1

B1

This Service manual is issued as a service guide for the models of the NA7D family listed above. Included are
schematics, alignment procedures, disassembly procedures, and a parts list.

CT-13R32

Panasonic

CT-13R32E

DP358

CT-13R32CE

DP358

CT-13R42E

DP358

CT-13R42CE

DP358

CT-13R52DE

EP358

Chassis

Models

CT-13R52

Note:  CT-13R42E/CE are identical to

CT-13R32E/CE, respectively, except for
cabinet color. (CT-13R42E/CE have
white cabinets).

Содержание CT-13R32CE




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды