manualshive.com logo in svg

Panasonic CSC18DKU - AIR CONDITIONER - SPLIT, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CSC18DKU - AIR CONDITIONER - SPLIT Скачать руководство пользователя страница 49

(Lack of refrigerant in the refrigeration cycle)

Procedure:

 1. 

Confirm that both the 3-way valves are set to the open
position.

 2. 

Connect the charge set to the 3-way valve’s service
port.

 • 

Leave the valve on the charge set closed.

 • 

Connect the charge hose with the push-pin to the
service port.

 • 

Confirm whether the pressure indicates more than 14.5
PSI (1 kg/cm

2

G).

 3. 

Connect the charge set’s centre hose to refrigerant
reclaiming equipment.

 4. 

Open the valve (Low side) on the charge set and loosen
the hose connected with the Refrigerant Reclaiming
Equipment to purge the air from the hose.

 5. 

Turn on refrigerant reclaiming equipment to collect the
refrigerant until the needle indicates 0 (no refrigerant is
remaining.)

11.4. Balance refrigerant of the 3-way valves

49

CS-C18DKU CU-C18DKU / CS-C24DKU CU-C24DKU

Содержание CSC18DKU - AIR CONDITIONER - SPLIT













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды