40
14 Servicing Mode
14.1. Auto OFF/ON Button
1. AUTO OPERATION MODE
The Auto operation will be activated immediately once the AUTO OFF/ON button is pressed. This operation can be used to
operate air conditioner with limited function if remote control is misplaced or malfunction.
2. TEST RUN OPERATION (FOR PUMP DOWN/SERVICING PURPOSE)
The Test Run operation will be activated if the AUTO OFF/ON button is pressed continuously for more than 5 seconds. A
"beep" sound will occur at the fifth seconds, in order to identify the starting of this operation.
The AUTO OFF/ON button may be used together with remote control to set/change the advance setting of air conditioner
operation.
3. REMOTE CONTROL NUMBER SWITCH MODE
The Remote Control Number Switch mode will be activated if the AUTO OFF/ON button is pressed continuously for 11
seconds (3 "beep" sounds will occur at the 11th seconds to identify the Remote Control Number Switch mode is in standby)
and press "RESET" button and then press any button at remote control to transmit and store the desired transmission code to
the EEPROM.
There are 4 types of remote control transmission code could be selected. The indoor unit will only operate when received
signal with same transmission code from remote control. This could prevent signal interference when there are 2 or more
units installed nearby together.
To change remote control transmission code, short or open jumpers at the remote control printed circuit board.
4. REMOTE CONTROL RECEIVING SOUND OFF/ON MODE
The Remote Control Receiving Sound OFF/ON mode will be activated if the AUTO OFF/ON button is pressed continuously
for more than 26 seconds (6 "beep" sounds will occurs at 26th seconds to identify the Remote Control Receiving Sound OFF/
ON mode is in standby condition) and press "Reset" button at remote control.
Press AUTO OFF/ON button to toggle remote control receiving sound.
- Short "beep": Turn ON remote control receiving sound.
- Long "beep": Turn OFF remote control receiving sound.
Содержание CS-PC30JKF
