Panasonic CS-E12RKUAW Скачать руководство пользователя страница 13

44 

12.2.4 

 Connect the Cable to the Indoor Unit 

1. The inside and outside connection cable can

be connected without removing the front grille.

2. Unscrew the conduit cover and fix the conduit

connector to conduit cover with lock nut, then
secure it against chassis.

3. Connecting wire between indoor unit and

outdoor unit should be UL listed or CSA
approved 4 conductor wires minimum AWG16
in accordance with local electric codes.

o

Ensure the colour of wires of outdoor unit
and terminal number are the same as the
indoor's repectively.

o

Earth lead wire shall be Yellow/Green
(Y/G) in colour and shall be longer than
other lead wires as shown in the figure for
electrical safety in case of the slipping.

Rear view for left piping installation

Drain cap

Drain hose

Adjust the piping slightly downwards.

Drain hose

Connection
cable

How to pull the piping and drain hose out, in case of embedded piping.

How to insert the connection cable and drain hose
in the case of left piping.

Cable

45

°

Drain
hose

Piping

(For right piping, follow the same procedure)

Sleeve for piping hole

Drain hose

Piping

Connection
cable

More than 45

9

/

32

"

(1150 mm)

Replace the drain hose

Indoor unit
drain hose

3/4" (20 mm) nominal PVC pipe
- Install incline downward more than 1°
- Apply PVC glue at the join.

Drain hose adapter

9

Close join by Vinyl Tape ( )

Join indoor drain hose to 3/4" (20 mm) nominal PVC pipe size
by using drain hose adapter

9

when necessary.

Drain hose adapter

9

usage

Remarks :
Make sure indoor unit drain hose & 3/4" (20 mm) nominal PVC pipe
are fully inserted to drain hose adapter

9

.

2

27

/

32

" (72 mm)

More

than

18

1

/

2

" (47

0 mm

)

Mo

re

than

45

9

/

32

"

(115

0 m

m)

M

o

re

than

2

7

9

/

16

"

(7

0

0

mm)

PVC tube
for drain
hose

Indoor unit

Piping

Cable

Apply putty or
caulking material
to seal the wall
opening.

Connection cable

Piping

PVC tube (VP-65) for piping
and connection cable

PVC tube for drain hose (VP-30)

PVC tube for drain
hose (VP-20)

Drain hose
from main unit

Terminals on the indoor unit

1

2

3

Colour of wires (Connecting wire)

Terminals on the outdoor unit

1

2

3

WARNING

This equipment must be properly earthed.

1

2

3

Earth Wire
longer than
others AC
wires for
safety
reason

Terminal
Board

Holder

Indoor and
outdoor
connection
cable

Chassis

Conduit
Connector

Conduit
Cover

Lock Nut

Rear Side of Indoor Unit

Содержание CS-E12RKUAW


















Отзывы: