21
E
N
G
L
I
S
H
22
E
N
G
L
I
S
H
33
32
CQ-C1200U/C1120U/C1110U/C1100U
CQ-C1200U/C1120U/C1110U/C1100U
❐
General
Power supply:
12 V DC (11 V–16 V), test voltage 14.4 V, negative ground
Current consumption:
Less than 2.2 A (CD play mode; 0.5 W
×
4 channels)
Maximum power output:
50 W
×
4 channels at 1 kHz, volume control maximum (CQ-C1200U/C1120U)
45 W
×
4 channels at 1 kHz, volume control maximum (CQ-C1110U/C1100U)
Tone adjustment range:
Bass:
±12 dB at 100 Hz
Treble:
±12 dB at 10 kHz
Suitable speaker impedance:
4–8
Ω
Preamp output voltage:
2.0 V (CD play mode; 1 kHz, 0 dB)
Output impedance:
200
Ω
Sub-Woofer output voltage:
2.0 V (CQ-C1200U)
Sub-Woofer output impedance: 200
Ω
(CQ-C1200U)
Dimensions (W
×
H
×
D):
7"
×
1
15
/
16
"
×
5
7
/
8
" (178
×
50
×
155 mm)
Weight:
3 lbs. 1 oz (1.4 k
g
)
❐
FM Stereo Radio
Frequency range:
87.9 MHz–107.9 MHz
Usable sensitivity:
11.0 dBf. (1.25 µV, 75
Ω
)
50 dB quieting sensitivity:
15.2 dBf. (1.6 µV, 75
Ω
)
Frequency response:
30 Hz–15 kHz (±3 dB)
Alternate channel selectivity:
75 dB
Stereo separation:
42 dB (1 kHz)
Image response ratio:
75 dB
IF response ratio:
100 dB
Signal/noise ratio:
70 dB
❐
AM Radio
Frequency range:
530 kHz–1 710 kHz
Usable sensitivity:
28 dB/µV (25 µV, S/N 20 dB)
❐
CD Player
Sampling frequency:
8 times oversampling
DA converter:
1 bit DAC system
Error correction system:
Panasonic super decoding algorithm
Pick-up type:
Astigma 3-beam
Light source:
Semiconductor laser
Wave length:
780 nm
Frequency response:
20 Hz–20 kHz (±1 dB)
Signal/noise ratio:
96 dB
Total harmonic distortion:
0.01 % (1 kHz)
Wow and flutter:
Below measurable limits
Channel separation:
75 dB
Above specifications comply with EIA standards.
Note:
Specifications and the design are subject to modification without notice due to improvements in technology.
Specifications
1
2
1
2
3
4
Switch off the power of the unit.
Remove the removable face plate.
q
Press
[
]
.
The removable face plate will
be opened.
w
Push the face plate to either the right or
left.
e
Pull it out towards you.
Remove the Trim Plate
u
with a screwdriver.
q
Insert the Dismounting plate
i
along
the grooves on both sides of the main
unit until “click” is heard.
w
Pull out the unit while pushing the plates
further inside.
Remove the unit by pulling with both hands.
Contact
q
Press
u
Trim Plate
Screwdriver
i
Dismounting plate
Insert the tab
end in the
outer groove.
“
Click”
q
Insert
w
Pull out
w
To Remove the Unit
5
