Preparation
Batter
y
Installation
Clock Setting
Pull the insulation film out from
the backside of the remote control
gently.
1
Set your car’s ignition switch
to the ACC or ON position.
C
C
A
N
O
\CQ-RX321W\ \CQ-RX322W\ \CQ-RX221W\ \CQ-RX222W\
\CQ-RX225W\ \CQ-RX121W\ \CQ-RX122W\
The 24-hour system is used for the clock.
1
Press
[DISP]
.
(clock display)
2
Hold down
[DISP]
for more than
2 seconds.
Hour blinks
3
Adjust the hour.
Hour entered
[
]
: sets the hour ahead.
[
]
: sets the hour back.
4
Press
[DISP]
.
Minute blinks
5
Adjust the minute.
Minute entered
[
]
: sets the minute ahead.
[
]
: sets the minute back.
6
Press
[DISP]
.
Completed
Notes:
• “ADJUST” is displayed before adjusting the clock.
• Hold down
[
]
or
[
]
to change numbers rapidly.
• When “NO USB” (
\CQ-RX321W\ \CQ-RX322W\
)
or “NO
DISC” is displayed, the clock cannot be adjusted.
Clock Display at Power Off
Press
[DISP]
to change the display.
Display off
Clock display (Default)
Note:
Battery Information:
Battery Type: Panasonic lithium battery (CR2025) (Included
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX321W\ \CQ-RX322W\
\CQ-RX225W\
\CQ-RX420W\
\CQ-RX320W\
\CQ-RX321W\ \CQ-RX322W\
\CQ-RX121W\
\CQ-RX122W\
The demonstration message appears for initial
use.
1
Set your car’s ignition switch to the ACC or
ON position.
2
Press
[SRC]
(PWR:
Power
)
.
3
Hold down
[VOL]
(PUSH SEL:
Select
)
for
2 sec. or more to open the function menu.
4
Press
[VOL]
(PUSH SEL:
Select
)
to select
DEMO.
5
Turn
[VOL]
counterclockwise.
For using the remote control, press
[0]
(
)
.
Notes:
• To return to the regular mode, press
[DISP]
.
• Refer to the section on “Function Settings”.
• When “NO USB” (
\CQ-RX420W\ \CQ-RX320W\
\CQ-RX321W\ \CQ-RX322W\
)
or “NO DISC” is displayed,
the Demonstration cannot be cancelled.
Cancellation of
Demonstration
2
Press
[SRC]
(PWR:
Power
)
.
First T
ime
Power On
[VOL]
selects a value in the audio menu.
(PUSH SEL)
(Push to select)
selects items in the audio menu.
[DISP]
(Display)
exits from the audio menu.
Audio Menu
Volume
(Setting Range: 0 to 40, Default: 18)
: Up
: Down
Bass
(Setting Range: –12 dB to +12 dB by 2 dB, Default: 0 dB)
: Increased
: Decreased
Treble
(Setting Range: –12 dB to +12 dB by 2 dB, Default: 0 dB)
: Increased
: Decreased
SQ (Sound Quality)
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
(Setting Range: FLAT/ROCK/POP/VOCAL/JAZZ/CLUB,
Default: FLAT)
(
“Sound Control”)
SQ Adjustment
(Tone/SQ adjustable range:
12 dB to
12 dB (by 2 dB))
Setting range:
SQ Low/Bass: ±12 dB (at 60 Hz, 80 Hz, 100 Hz, 200 Hz)
SQ Mid:
±12 dB (at 500 Hz, 1 kHz, 2 kHz, 3 kHz)
SQ High/Treble: ±12 dB (at 10 kHz, 12 kHz, 15 kHz, 18 kHz)
/
: center frequency up/down
[
]
[
]
: Band selection
[
]
[
]
: Level up/down
Balance
(Setting Range: 15 levels each, Default: CNT (center))
: Right enhanced
: Left enhanced
Fader
(Setting Range: 15 levels each, Default: CNT (center))
: Front enhanced
: Rear enhanced
Notes:
• The volume can also be adjusted directly using
[VOL]
on the main unit. (
“General”)
• For further information on SQ (Sound Quality) settings, refer to “Sound Control”.
• Do not activate SQ and Bass/Treble at the same time to avoid causing sound distortion.
1
Press
[VOL] (PUSH SEL)
to open the audio menu.
Note:
If no operation takes place for more than 5 seconds in audio setting (2 seconds in the volume adjustment,
10 seconds in the SQ adjustment), the display returns to the regular mode.
2
Press
[VOL] (PUSH SEL)
to select a
mode to be adjusted.
3
Turn
[VOL]
clockwise or counterclockwise to
adjust.
Audio Settings
Notes:
\CQ-RX420W\
• The sequence and contents of setting items may depend
on the conditions of devices to be connected. For further
information, refer to the
System Upgrade Guidebook
or
the instruction manuals for the devices to be connected.
\CQ-RX320W\ \CQ-RX321W\ \CQ-RX322W\
\CQ-RX220W\ \CQ-RX221W\ \CQ-RX222W\ \CQ-RX225W\
• If the fader is set to front, the pre-amp. output (rear) is
decreased.
Radio Data System (RDS) in FM Broadcasting
What is RDS?
AF (Alternative
Frequency)
Useful functions such as
AF, TA, PTY
are available in the RDS (Radio Data System)-ready areas.
AF (Alternative Frequency)
The following functions are available when the AF mode is
active (
lights).
• When receiving conditions become bad, a station with better
receiving conditions is automatically tuned in to.
• When executing APM, only RDS stations are selected.
• When calling up a preset station, a best receiving station is
selected automatically. (
BSR
Best Stations Research)
Notes:
• The AF sensitivity can be adjusted.
• The AF available range can be adjusted. (
“Function Settings”)
TA (Traffic Announcement)
The following functions are available when the TA mode is
active (
lights).
• A TP station is automatically searched for and received at
the instant of toggling the TA mode on if you are receiving a
non-TP station or TP station with poor reception.
• When executing station search or APM, only TP stations are
selected.
• Setting to TA on with the unit in another mode, it will
automatically switch to radio mode and output the traffic
announcement when the traffic announcement begins. The
traffic announcement having finished, the unit will return to
the previous mode. (TA Standby Mode)
AF Level
Hold down
[TA] (AF)
for more than 2 seconds to select AF
level.
PI Seek (Programme Identification Seek)
If reception becomes poor when tuning in a preset station,
press the same preset number button. The same station with
better reception will be searched for.
Press same preset number button again to cancel.
(blinks)
Note:
For PI Seek, cancel the TA mode first, then execute PI
Seek.
PTY (Programme Type)
The following functions are available when the PTY mode is
active.
• The PTY of receiving station appears.
• Programs can be searched for by PTY.
Note:
PTY language can be selected. (
“Function Settings”)
Other functions of RDS
CT (Clock Time)
The clock is automatically adjusted.
PS (Programme Service Name)
As well as the frequency, the name of the broadcast station
appears.
EON (Enhanced Other Network)
RDS information is updated constantly in response to the
current position.
EON-TA
Traffic information from the current and other network
stations can be received.
Emergency Announcement Reception
Emergency announcement automatically appears on the
display when it is received.
Some FM stations are broadcasting added data compatible with RDS. This radio set offers convenient functions using such data.
RDS service availability varies with areas. Please understand if RDS service is not available in your area, the following service is
not available, either.
The following functions are available when receiving RDS stations.
PTY On/Off
Holding down
[DISP] (PTY)
for more than 2 seconds
toggles PTY mode on and off.
Programme Search by PTY
Programs can be searched for by use of PTY that has been
originally preset.
Press
[1]
to
[6]
to select PTY in the PTY
mode.
Programme Type
Contents
1
NEWS
NEWS
2
SPEECH
AFFAIRS, INFO, EDUCATE, DRAMA,
CULTURE, SCIENCE, VARIED,
WEATHER, FINANCE, CHILDREN,
SOCIAL, RELIGION, PHONE IN,
TRAVEL, LEISURE, DOCUMENT
3
SPORT
SPORT
4
POP M
POP M
5
CLASSICS
CLASSICS
6
MUSIC
ROCK M, EASY M, LIGHT M,
OTHER M, JAZZ, COUNTRY,
NATION M, OLDIES, FOLK M
Another station in the same PTY is searched for by pressing
[BAND]
.
Notes:
• When there is no corresponding programme type station,
“NONE” is displayed.
• A desired PTY appears for 5 seconds.
• Preset contents are changeable.
Detailed PTY Selection
1
Press
[
]
or
[
]
to select PTY.
SPEECH
MUSIC
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
EASY M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATION M
OLDIES
FOLK M
DOCUMENT
2
Press
[BAND]
.
Search starts.
Notes:
• To stop searching, press
[BAND] (SET)
.
• When there is no corresponding programme type station,
“NONE” is displayed.
PTY Preset Change
Original PTY presets can be changed as you like.
1
Select a PTY that you would like to preset.
2
Follow the procedure of ordinary
presetting. (
“Station Preset” in “Radio
(AM/FM)”)
Low level AF operating sensitivity. (Default)
High level AF operating sensitivity.
When the AF network of an RDS station is not required.
PTY (Programme T
ype)
Display Change
Press
[DISP]
to change the display.
Notes:
• For scrolling text, press
[3] (SCROLL)
.
• “NO TEXT” is displayed when there is no information on the disc.
Player Source Display
Random, Repeat, Scan
Random Play
All the available songs (tracks/files) are played in a random
sequence.
Press
[4] (RANDOM)
.
Press again to cancel.
Folder Random Play (MP3/WMA/AAC)
All the available files in current folder are played in a random
sequence.
Hold down
[4] (RANDOM)
for more than
2 seconds.
Hold down again to cancel.
Repeat Play
The current song (track/file) is repeated.
Press
[6] (REPEAT)
.
Press again to cancel.
Folder Repeat Play (MP3/WMA/AAC)
The current folder is repeated.
Hold down
[6] (REPEAT)
for more than
2
seconds.
Hold down again to cancel.
Scan Play
The first 10 seconds of each songs (tracks/files) is played in
sequence.
Press
[5] (SCAN)
.
Press again to cancel.
Folder Scan Play (MP3/WMA/AAC)
From the next folder, the first 10 seconds of the first file in
each folder is played in sequence.
Hold down
[5] (SCAN)
for more than
2 seconds.
Hold down again to cancel.
Disc Player
(CD-DA disc):
Disc Player (MP3/WMA/AAC
disc):
CD-DA Mode Display
Track number
Play time
Play Mode indicators
Play Mode indicators
Lights when folder random/repeat/scan is on.
Folder number
File number
MP3/WMA/AAC Mode Display
Normal
Disc title
Track title
Clock
Normal
Play time
Folder name/
Album*
File name/
Title, artist*
Clock
*ID3/WMA/AAC Tag On/Off
Hold down
[3]
for more
than 2 seconds.
album title and song title/
artist name are displayed.
(Default)
folder name/file name are
displayed.
Lights when the disc is loaded.
Player (Disc Player)
1
Press
[SRC]
to select the Disc Player
source.
2
Select a desired portion.
Track/File Selection
Press
[
]
/
[
]
.
Note:
To perform fast forward/reverse, hold down either of
them.
Disc Player (CD-DA disc):
Previous/next track
Disc Player (MP3/WMA/AAC disc):
Previous/next file
Folder Selection (MP3/WMA/AAC)
Press
[
] / [
]
.
Note:
A disc which has both CD-DA data and MP3/WMA/AAC data on it
may not be reproduced normally.
\CQ-RX321W\ \CQ-RX322W\ \CQ-RX221W\ \CQ-RX222W\ \CQ-RX225W\
\CQ-RX121W\ \CQ-RX122W\
Note:
The power will be turned on automatically when a disc is loaded.
[
] [
]
skip to the previous/next track/file in
the player mode.
Hold down either of them for fast
reverse/fast forward.
[
]
(Eject)
ejects the disc.
[DISP]
(Display)
switches the information on the display.
[
] [
]
skip to the previous/next folder.
[4] (RANDOM)/[5] (SCAN)/[6] (REPEAT)
toggles on/off each play mode.
[3] (SCROLL)
scrolls the information on display.
(
)
(Play/Pause)
toggles pause/play in the player source.
[SRC]
(Source)
selects a source.
Operation Flow
Printed side up
Notes:
•
Do not insert a disc when the
indicator lights.
•
Refer to the section of “Notes on Discs” and “Notes on MP3/WMA/
AAC”.
•
This unit does not support 8 cm discs.
• If you insert an 8 cm
disc and cannot eject it, turn ACC of your car off
once and turn it on again, then press
[
]
(Eject).
• Do not insert foreign matter into the disc slot.
Playable Audio File
CQ-RX420W
MP3/WMA/AAC
CQ-RX320W
MP3/WMA
CQ-RX321W
MP3/WMA
CQ-RX322W
MP3/WMA
CQ-RX220W
MP3/WMA
CQ-RX221W
MP3/WMA
CQ-RX222W
MP3/WMA
CQ-RX225W
MP3/WMA
CQ-RX121W
MP3/WMA
CQ-RX122W
MP3/WMA
Notes for AAC playback is only for the model CQ-RX420W.
Pause
Press
[BAND] (
)
.
Press again to cancel.
Disc slot
takes a disc in with the
printed side facing up.
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
SQ Changeover
1
Press
[VOL]
(
PUSH SEL:
Select) to
open the audio menu.
2
Press
[VOL]
(
PUSH SEL:
Select) to select
SQ.
3
Turn
[VOL]
to select the sound type
as follows.
Press
[DISP]
to return to the regular mode.
Note:
Please refer to “Audio Settings” for the adjustment to
each speaker.
SQ Selection Based on Genre
SQ (Sound Quality)
SQ Adjustment
You can adjust the characteristics of the currently selected
sound type (SQ). (
Above)
It is also possible to preset up to 5 different adjusted SQs.
SQ3 (3-Band Sound Quality)
Center frequency and level are adjustable in each of 3 bands.
This lets you fine-tune sound quality for each genre to suit
car-interior acoustics and your personal preferences.
Tone/SQ adjustable range:
12 dB to
12 dB (by 2 dB)
SQ Low/Bass:
±12 dB (at 60 Hz, 80 Hz, 100 Hz, 200 Hz)
SQ Mid:
±12 dB (at 500 Hz, 1 kHz, 2 kHz, 3 kHz)
SQ High/Treble: ±12 dB (at 10 kHz, 12 kHz, 15 kHz, 18 kHz)
• The bass/treble control level of each frequency is fixed to the
frequency that has been selected for SQ.
To return an adjusted SQ to the default setting
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
Select the SQ which is to be returned to the default setting.
(Follow steps
1
to
3
in “SQ Changeover”.
Above)
Hold down
[BAND]
for 2 sec. or more.
\CQ-RX321W\ \CQ-RX322W\ \CQ-RX221W\ \CQ-RX222W\
\CQ-RX225W\ \CQ-RX121W\ \CQ-RX122W\
Press
[SQ]
, and select the SQ which is to be returned to
the default setting. (Only for main unit)
Hold down
[BAND]
for 2 sec. or more.
Notes:
• You cannot save any SQ presetting value in
[1]
button.
• Any SQ adjustments will not change the call up screen
names such as ROCK and JAZZ.
• Do not activate SQ and Bass/Treble at the same time to avoid
causing sound distortion.
1
Press
[VOL]
(
PUSH SEL:
Select)
to open the audio menu.
2
Press
[VOL]
(
PUSH SEL:
Select) to select
SQ SET.
3
Adjust each band.
/
: center frequency up/down
[
]
[
]
: Band selection
[
]
[
]
: Level up/down
Level
Frequency
4
Hold down the numeric button
[2]
to
[6]
for
2 sec. or more.
• The adjusted SQ is preset in the number of the selected
button, and return to the regular mode resumes.
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
• SQ Adjustment will not be saved unless it is preset. Always
preset after making adjustments.
\CQ-RX321W\ \CQ-RX322W\ \CQ-RX221W\ \CQ-RX222W\
\CQ-RX225W\ \CQ-RX121W\ \CQ-RX122W\
• When you suspend the SQ preset adjustment, each level
remains your recent adjustment until a new SQ presetting
operation is performed or you call up the SQ preset.
Sound Control
(FLAT) flat frequency response:
does not emphasize any part. (Default)
(ROCK) speedy and heavy sound:
exaggerates bass and treble.
(POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
(VOCAL) clear sound:
emphasizes middle tone and slightly emphasizes
treble.
(JAZZ) jazz-specific deep sound:
sound with emphasis on sharpness of high-hat and
echo saxophone.
(CLUB) club and disco-specific sound:
reproduction of realism being in a club.
General
[VOL]
(Volume)
[SRC]
(Source)
selects a source.
[PWR]
(Power)
toggles power on/off.
Power On/Off
Set your car’s ignition switch to the ACC or ON position.
Power on:
Press
[SRC] (PWR)
.
Power off:
Hold down [SRC] (PWR) for more
than 1 second.
General Operations
Remote Control Sensor
[TA/AF]
\CQ-RX420W\ \CQ-RX320W\
\CQ-RX220W\
(
“Radio
Data System (RDS) in FM
Broadcasting”)
AUX1
Connector
(3.5 mm
stereo)
From line output of external sound/audio device (ex.
Silicon-audio player, HDD player, etc.)
Note:
The connector is labeled “AUX1”, but it appears on
the display as “<AUX IN>”.
(
Below)
Caution
•
Set the volume level to low enough before the AUX connection is completed.
Failure to observe this, the loud noise may come out and damage your
speakers and your hearing.
\CQ-RX220W\ \CQ-RX221W\ \CQ-RX222W\ \CQ-RX225W\
\CQ-RX121W\ \CQ-RX122W\
Radio
Disc Player
AUX
*
Volume Adjustment
(Setting Range: 0 to 40, Default: 18)
Turn
[VOL]
.
\CQ-RX320W\ \CQ-RX321W\ \CQ-RX322W\
Radio
Disc Player
AUX
*
USB Connector
(
Right)
Press
[SRC]
to change the source.
\CQ-RX420W\
Radio
Disc Player
System-up
Connector
AUX 1
*
USB Connector
(
Right)
(
Right)
Note:
Select USB Connector mode to operate the iPod
series connected with USB connector.
(
System Upgrade
Guidebook)
\CQ-RX420W\
Note:
For information about connectable devices, refer to the
System
Upgrade Guidebook
or the instruction manual for each device.
\CQ-RX320W\ \CQ-RX321W\ \CQ-RX322W\
Note:
For information about connectable devices, refer to the
Operating
Instructions USB
or the instruction manual for each device.
Source Selection
System-up Connector
\CQ-RX420W\
When an optional device is connected:
Shift to connected device
When connecting CD changer
When connecting iPod
When connecting Bluetooth Unit
OR
When an expansion module is connected:
The devices connected to the ports 1 to 4 are activated in
sequence after shifting to AUX2 (device connected to the
AUX terminal of the expansion module).
USB Connector
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX321W\ \CQ-RX322W\
When an optional USB memory is connected:
When loading MP3/WMA/AAC data
\CQ-RX420W\
When loading MP3/WMA data
\CQ-RX320W\ \CQ-RX321W\ \CQ-RX322W\
When an optional USB memory is not connected:
AUX IN*:
\CQ-RX420W\
\CQ-RX320W\ \CQ-RX321W\ \CQ-RX322W\
\CQ-RX220W\ \CQ-RX221W\ \CQ-RX222W\ \CQ-RX225W\
\CQ-RX121W\ \CQ-RX122W\
[BAND]
selects a band in the radio source.
[APM]
(Auto Preset Memory)
executes APM in the radio source. (Hold it
down for more than 2 seconds.)
[SRC]
(Source)
selects a source.
Preset buttons [1]
to
[6]
selects a preset station in the radio source,
and presets the current station. (Hold it down for more than 2 seconds.)
[TUNE
] [TUNE
]
down/up the frequency. (Hold it down for more
than 0.5 seconds and release it for seek tuning.)
[DISP]
(Display)
switches the information on the
display.
1
Press
[SRC]
to select the radio source.
2
Press
[BAND]
to select a band.
3
Select a station.
Radio (AM/FM)
AM (LW/MW) mode:
Band/frequency
CT
(Clock Time)
lights while receiving an FM
stereo signal.
Band
Frequency
Preset Number
Display Change
Station Preset
Frequency Adjustment
[TUNE
]
: Lower
[TUNE
]
: Higher
Note:
Hold down for 0.5 sec. or more and release for station
search.
Preset Station Selection
Press the corresponding preset button from
[1]
to
[6]
to tune in a preset station.
Up to 6 stations can be preset in AM, FM1, FM2, and FM3 respectively.
Preset stations can be simply called up by pressing
[1]
to
[6]
.
Auto Preset Memory (APM)
With this operation, stations with good receiving conditions
can be automatically stored in the preset memory.
1
Select a band.
2
Hold down
[BAND] (APM)
for more than
2 seconds.
The preset stations under best receiving conditions are received
for 5 seconds each after presetting the stations (SCAN). To stop
scanning, press one of the buttons from
[1]
to
[6]
.
Manual Station Preset
1
Tune into a station.
2
Hold down one of the preset buttons from
[1]
to
[6]
for more than 2 seconds.
(blinks once)
Note:
New stations overwrite existing saved stations.
Radio Source Display
Press
[DISP]
to change the display.
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
FM (not RDS) mode:
Band/
frequency
PS
CT
RDS mode:
PS
(Programme
Service name)
Band/frequency
CT
Function Settings
[VOL]
selects a value in the function menu.
(PUSH SEL)
(Push to select)
selects items in the function menu.
[DISP]
(Display)
exits from the function menu.
FM Monaural
[FM]
: MONO ON
(
lights.)
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
Noise is significantly decreased when weak signals are
received from an FM broadcast station.
: MONO OFF
(Default)
FM Local
[FM]
: LOCAL ON
(
lights.)
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
Only stations with good reception are detected in seek
tuning.
: LOCAL OFF
(Default)
(
Continued below)
1
Hold down
[VOL] (PUSH SEL)
for 2 sec. or more to open the function menu.
Note:
If no operation takes place for more than 5 seconds in function setting, the display returns to the regular mode.
2
Press
[VOL] (PUSH SEL)
to select a
mode to be adjusted.
3
Turn
[VOL]
clockwise or counterclockwise to
adjust.
Direct Access
A track (CD mode), file, folder (MP3/WMA/AAC mode) can
be directly selected.
Example:
Track number 5
1
Press
[#] (NUMBER)
.
2
Press
[5]
.
3
Press
[BAND] (SET)
.
Notes:
• To suspend direct selection, press
[DISP]
.
• For folder selection, enter a number after pressing
[#]
(NUMBER)
twice.
Functions only on Main unit
The following functions are not available on remote control
unit.
• Scroll
• Disc eject
• Tag on/off
\CQ-RX321W\ \CQ-RX322W\ \CQ-RX221W\ \CQ-RX222W\
\CQ-RX225W\ \CQ-RX121W\ \CQ-RX122W\
• SQ selection
Battery Replacement
Remove the battery holder with
the remote control unit placed on
a flat surface.
Stick your thumbnail into the
groove, and push the holder
in the direction of the arrow,
and at the same time.
Pull it out in the direction
of the arrow using a tough
pointed object.
Remote Control Unit
Functions
Notes:
• This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
• Aim the remote control at the remote sensor and operate it.
[0] to [9]
selects a preset station (1 to 6),
presets the current station (Hold it down for more than
2 seconds.),
inputs the number in direct selection.
[#] (NUMBER)
executes the direct selection.
[RANDOM] [SCAN] [REPEAT]
toggles on/off each play mode.
[
] [
]
down/up the frequency (Hold it down for more than
0.5 seconds and release it for seek tuning.)
[
]
[
]
skip to the previous/next folder in player mode.
[
] [
]
skip to the previous/next track/file in player mode.
Hold
it down for fast reverse/fast forward.
[BAND] (SET)
selects a band in the tuner source, toggles pause/play in player source,
executes the APM (Auto Preset Memory) in tuner source
(Hold it down for more than 2 seconds).
[MENU] (SEL:
Select
)
selects the items in the audio menu.
[VOL]
(volume)
adjusts the volume, and selects the
value in the audio menu, etc.
[MUTE]
toggles mute on/off.
(Only for remote control unit)
Note:
You can select mute or
attenuation. (
“Function Settings”)
[DISP]
(Display)
switches the information on display,
and exits the audio menu.
[SRC] (SOURCE)
selects a source.
(POWER)
toggles power on/off.
Warning
Keep batteries and insulation film out of reach of infants.
Batteries and insulation film can be ingested, so keep
them out of the reach of infants. If an infant ingests a
battery or insulation film, please seek immediate medical
attention.
Caution
• Remove and dispose of an old battery immediately.
• Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
• Follow local regulations when disposing of a battery.
• Improper use of batteries may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Notes:
Battery Information:
Battery Type: Panasonic lithium battery (CR2025) (Included
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
Tough pointed object
Back side
1
2
Put a battery in the
case with (+) side
facing up.
Put the case back.
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX321W\
\CQ-RX322W\ \CQ-RX225W\
AM Local
[AM]
: LOCAL ON
(
lights.)
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
Only stations with good reception are detected in seek
tuning.
: LOCAL OFF
(Default)
Region
]RDS]
: The frequency
is changed only for
programs within
the region.
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
Note:
When the Region mode is switched from OFF to
ON or vice versa, the AF mode turns on automatically.
: The frequency
is changed also
for programs
outside the region.
(Default)
PTY Language
]RDS]
: English
(Default)
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
: Swedish
Demonstration
: On (Default)
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX321W\
\CQ-RX322W\ \CQ-RX121W\ \CQ-RX122W\
You can set up the monitor to display or hide the
demonstration screen.
Note:
Button operation with either the main unit or
remote control allows users to cancel the demonstration
screen for 20 seconds and enable the selected operation
even in the demo-on mode.
: Off
Mute/Attenuation
: Volume down
by 10 steps
You can select mute or attenuation.
: Volume off
(Default)
AUX1 Skip
: On (Skip
disabled.) (Default)
\CQ-RX420W\
If AUX1 is not used, the AUX1 mode is skipped when
selecting the source.
: Off (Skip
enabled.)
AUX Skip
: On (Skip
disabled.) (Default)
\CQ-RX320W\ \CQ-RX321W\ \CQ-RX322W\
\CQ-RX220W\ \CQ-RX221W\ \CQ-RX222W\
\CQ-RX225W\ \CQ-RX121W\ \CQ-RX122W\
If AUX is not used, the AUX mode is skipped when
selecting the source.
: Off (Skip
enabled.)
Function Menu
TA On/Off
Pressing
[TA]
toggles TA on and off.
Notes:
• This operation is not adjustable by the remote control.
• Traffic information is available in monaural.
• Adjust the TA volume only while receiving a TA.
Traffic Information Only (TA Mute)
For listening to only traffic information, activate TA and set the
volume to 0 in FM mode.
Once traffic information starts, the volume changes to the TA
volume.
T
A
(T
raffic
Announcement)
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
Clock Setting
\CQ-RX420W\ \CQ-RX320W\ \CQ-RX220W\
The 24-hour system is used for the clock.
1
Select the radio AM mode. (
“Radio
(AM/FM)”).
2
Press
[DISP]
.
(clock display)
3
Hold down
[DISP]
for more than
2 seconds.
Hour blinks
4
Adjust the hour.
Hour entered
[
]
: sets the hour ahead.
[
]
: sets the hour back.
5
Press
[DISP]
.
Minute blinks
6
Adjust the minute.
Minute entered
[
]
: sets the minute ahead.
[
]
: sets the minute back.
7
Press
[DISP]
.
Completed
Notes:
• “NO CT” is displayed before adjusting the clock.
• When a broadcast of FM Radio Data System is received,
the clock is adjusted automatically by the Clock Time
service.
• Hold down
[
]
or
[
]
to change numbers rapidly.
\CQ-RX321W\ \CQ-RX322W\ \CQ-RX221W\ \CQ-RX222W\ \CQ-RX225W\ \CQ-RX121W\ \CQ-RX122W\
Radio mode display (Default)
Clock display
Operation Flow
You have 6 preset modes (FLAT, ROCK, POP, VOCAL, JAZZ,
CLUB). You can customize your settings for these and save
them for instant recall.
Notes:
• To return to the regular mode, press
[DISP]
.
\CQ-RX420W\
• The sequence and contents of setting items
may depend on the conditions of devices to be
connected. For further information, refer to the
System Upgrade Guidebook
or the instruction
manuals for the devices to be connected.
\CQ-RX321W\ \CQ-RX322W\ \CQ-RX221W\ \CQ-RX222W\
\CQ-RX225W\ \CQ-RX121W\ \CQ-RX122W\
SQ Changeover
1
Press
[SQ]
to activate the SQ selection mode.
2
Press
[SQ]
to select the sound type as follows.
(
Left)
Press
[DISP]
to return to the regular mode.
Notes:
• After pressing
[SQ]
on the main unit, you can also select a sound
type by pressing the preset buttons
[1]
to
[6]
.
• Please refer to “Audio Settings” for the adjustment to each
speaker.
\CQ-RX321W\
\CQ-RX121W\
[SQ]
(Sound Quality)
selects a sound type (SQ).
Notes:
• New stations overwrite existing saved stations.
• To store non-RDS stations with Auto Preset Memory (APM), set the AF level
setting to OFF. (
“Radio Data System (RDS) in FM Broadcasting”)
