Security Warning window on Microsoft Windows XP Service Pack 2
To view a video (Motion JPEG), ActiveX Controls must be installed. Follow the steps shown below to install ActiveX Controls.
Click the warning displayed above the tabs, and click [Install
ActiveX Control...].
Click [Install].
4.
Mount the camera.
The camera can be mounted in the following ways.
•
Do not mount the camera where the sun light directly hits the camera or in
outdoor-type housing without a temperature control system. The camera
may malfunction due to high temperature.
•
When you mount the camera, always hook the AC adaptor cord to the
hook.
•
This product is for indoor use only. Do not use it outdoors.
•
The camera may become warm. This is not a malfunction.
•
Mount the camera where the AC adaptor can reach a power outlet, or use an
extension cord (customer-provided).
•
Do not mount the camera upside down, since the image will be displayed upside
down.
Note
Make sure the indicator is
always in the upper right
corner.
Top
Bottom
Hook for
AC adaptor cord
Stand Mount
Tripod Mount
Stand/Tripod
Mounting Hole
Flexible
Stand
Disconnect all cables from the camera. Reconnect the cables after mounting the
camera.
Note
Loosen the Position Lock
located on the rear side of
the flexible stand.
•
Do not use a tripod screw
with a thread of 6 mm or
more. This may damage the
Stand/Tripod mounting hole.
•
The camera cannot be
mounted depending on the
shape of the camera
platform.
Adjust the angle, then fasten
the Position Lock.
Stand/Tripod
Mounting Hole
Tripod
(customer-
provided)
Mounting
Screw
Position
Lock
Turn the Mounting Screw to
attach the camera.
Note
Ceiling Mount
• Do not mount the camera upside down, since the image will be displayed
upside down.
• We recommend only mounting the camera using the provided hardware.
Mounting in any other manner may cause the camera to fall, resulting in
personal injury or damage to the camera.
• To reduce the load on the mounting hardware, dress the cables neatly and
secure with tape.
• Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
Note
• Do not mount the camera on a soft
material. The camera may fall and
be damaged.
• Use appropriate screws for the
material of the ceiling.
Mount the flexible stand firmly to the
ceiling with the two screws (included).
Loosen the Position Lock located
on the rear side of the flexible stand,
and turn the Mounting Screw to
attach the camera.
Adjust the angle, then fasten
the Position Lock.
Connect the AC adaptor cord and
the Ethernet cable to the camera.
Dress the cables neatly and secure
with tape (customer-provided).
Screws
Allow sufficient space
between the wall and the
flexible stand to turn the
Position Lock.
Stand/Tripod
Mounting Hole
Position Lock
Tape
(customer-provided)
Mounting Screw
Position Lock
Wall Mount
• Do not mount the camera upside down, since the image will be displayed
upside down.
• We recommend only mounting the camera using the provided hardware.
Mounting in any other manner may cause the camera to fall, resulting in
personal injury or damage to the camera.
• To reduce the load on the mounting hardware, dress the cables neatly and
secure with tape.
• Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
Note
• Do not mount the camera on a soft
material. The camera may fall and
be damaged.
• Use appropriate screws for the
material of the wall.
Mount the flexible stand firmly to the
wall with the two screws (included).
Loosen the Position Lock located
on the rear side of the flexible stand,
and turn the Mounting Screw to
attach the camera.
Connect the AC adaptor cord and
the Ethernet cable to the camera.
Dress the cables neatly and secure
with tape (customer-provided).
Adjust the angle, then fasten
the Position Lock.
Screws
Allow sufficient space between the
ceiling and the flexible stand to turn
the Position Lock.
Position Lock
Tape
(customer-provided)
Stand/Tripod
Mounting
Hole
Indicator
Mounting
Screw
Position
Lock
