Panasonic AV-HS60C3G, Руководство по эксплуатации

Страница: 119 / 176

– 119 –
Chapter 7 Configuring Operations — Setting the operation mode
FTB (Fade to Black)
For DSKPGM1 and DSKPGM2 outputs, fade out from the program image to the black background screen, and fade in from the black ground screen
to the program image. While the settings and transition are performed by the menu, use the macro memory to assign to certain buttons to execute
transition.
1
Select the <OPR> button
→
[OTHER SETTINGS]
→
[Transition] tab.
2
Select an item in [Source] in the [FTB] column.
f
Select the image for fading out.
[Still1], [Still2] Uses still image video memory (Still1, Still2).
[Clip1], [Clip2] Uses moving image video memory (Clip1, Clip2).
[CBGD1], [CBGD2] Uses the color background.
[White] Uses the white background.
[Black] Uses the black background.
3
Set [Time] in the [FTB] column.
f
Set the transition time.
4
Set [FTB On] in the [FTB] column.
f
When [FTB On] is selected, the screen fades out to the image selected in the step
2
at a specified transition time.
If [FTB On] is selected when the image selected in the step
2
is on the screen, the screen fades in to the program image.
If [FTB On] is selected during transition, the transition direction is reversed.
@ @ NOTE
t
If an item other than [White] or [Black] is selected in [Source] in the [FTB] column, the corresponding crosspoint buttons will light in red while [FTB On]
is set.
AUX1 to AUX4 bus transitions
In the AUX1 to AUX4 buses, MIX transition is available.
1
Select the <OPR> button
→
[OTHER SETTINGS]
→
[Transition] tab.
2
Select an item in [AUX1] to [AUX4] in the [AUX Trans] column.
[OFF] Disables the MIX translation.
[ON] Enables the MIX translation.
3
Set [AUX1] through [AUX4] in the [Trans Time] column.
f
Set the transition time.
r
AUX bus transition operation
CG
3V CG
4V STIL
1V
STIL
2V
V5 V6
CG
1V CG
2V
ME1 ME2 ME3 ME4
CLIP
3V
CLIP4
V
BC1 BC2
DSK4
F/S
DSK3
F/S
DSK2
F/S
DSK1
F/S
STIL
3V
STIL
4V
CLIP
1V
CLIP
2V
V1 V2 V3 V4 C9 C10 C11 C12 C9 C10 C11 C12 C9 C10 C11 C12
AUX
7/8
AUX
5/6
AUX
3/4
AUX
1/2
AUX
17/18
AUX
15/16
AUX
13/14
AUX
11/12
AUX
9/10 USK3
F/S
USK2
F/S
USK1
F/S
AUX
23/24
AUX
21/22
AUX
19/20
USK4
F/S
MCRO DISP
VMEM
F/S
Lights in the Preset tally color
Blinks in the Low tally color (during transition)
Set [AUX1] to [AUX4] to [ON] in the [AUX Trans] column, then select sources with the relevant AUX bus crosspoint buttons.
At this time, the MIX transition is performed at the transition time specified in [AUX1] to [AUX4] in the [Trans Time] column.
During transition, KEY crosspoint buttons denoting the transition source lights in the Preset tally color, and the KEY bus crosspoint buttons denoting the
transition target source lights in the Low tally color.
When the transition is completed, the transition source button goes off, and the transition target button lights in the Low tally color.
When another signal is selected during transition, the transition processing continues from that midway point.
Switching the ME area in the Control Panel AV-HS60C2/AV-HS60C4
Switch the ME1 and ME2 in the Control Panel AV-HS60C2/AV-HS60C4.
f
The following figure shows the area that can be switched.