Panasonic AKW8115 Скачать руководство пользователя | Manualshive

Страница: 37 / 61

background image

KW8M Eco-POWER METER (1A/5ACT input type)

29

6.1.2 Instantaneous Electric Power

・

It displays the Instantaneous electric power.

・

Press <SHIFT/

▽

> to shift active power, reactive power, apparent power.

Instantaneous

active power (kW)

Instantaneous reactive power (kvar)

Instantaneous

apparent power (kVA)

[kW]
Lighting

[kvar]

Lighting

[kVA]

Lighting

*Instantaneous reactive power is “

－

(minus)” value when leading phase and it shows “

－

(minus)“ in the

display. It is “+ (plus)” value when lagging phase, but it doesn’t show “+ (plus)”.

6.1.3 Current

・

It displays the current value of the load.

・

Press <SHIFT/

▽

> to change L1(CT1)-phase, L2(CT2)-phase, L3(CT3)-phase current.

*Before start measuring, select phase and wire system according to the measured load.

When 1P3W or 3P3W is selected, it doesn’t measure 1P2W system correctly. When 3P4W system is
selected, it doesn’t measure 1P2W, 1P3W, 3P3W system correctly.
Select phase and wire system according to the measured system. (Refer to the explanation of setting
mode.)

[A]

Lighting

・

When input current exceeds 150%F.S. at each range,

「

- - - -

」

will be displayed.

«
...
35
36
37
38
39
...
»

Содержание AKW8115






























































Отзывы:

Нет отзывов

Похожие инструкции для AKW8115

Бренд: Kawai Страницы: 70

Бренд: Bacharach Страницы: 19

Бренд: Callaway Страницы: 11

Бренд: Mini Страницы: 20

Бренд: Omega Страницы: 31

Бренд: marposs Страницы: 58

SoundTrack LxT N/Forcer

Бренд: Larson Davis Страницы: 12

Бренд: Mark-10 Страницы: 26

Бренд: SKF Страницы: 12

Бренд: 3M Страницы: 168

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренд: yellow jacket Страницы: 16

Бренд: VECTECH Страницы: 10

Бренд: WAGNER Страницы: 4

Xtrinsic MMA8491Q

Бренд: Freescale Semiconductor Страницы: 4

Бренд: Swema Страницы: 12

Бренд: Delmhorst Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды