Palfinger MBB C 500 VAN Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 196

background image

29

Extending the Stabilizer Feet at Your
Vehicle

Vehicles with Mechanical Stabilizer Feet

Mechanical stabilizer feet prevent chassis damage

.

When load-

ing the vehicle, the stabilizer feet skid through.
To extend the mechanical stabilizer feet:



Loosen the clamping device.



Lower the stabilizer feet until they touch the ground.



Hand-tighten the clamping device.

Vehicle with Hydraulic Stabilizer Feet



To extend the hydraulic stabilizer feet, see “Operation Us-
ing One-hand Control and Hydraulic Stabilizer Feet” from
p. 54.

CAUTION!

Damage to the vehicle!

The vehicle chassis frame can be damaged by insufficient
carrying capacity of the ground or by incorrectly adjusted hy-
draulic stabilizer feet.



Make sure that the carrying capacity of the ground is ap-
propriate for the stabilizer feet!



Never lift up the vehicle by means of the hydraulic stabi-
lizer feet!



Readjust the stabilizer feet several times while loading the
vehicle.

CAUTION!

Risk of injury or material damage for vehicles with air
suspension

When you do not block the air suspension of your vehicle, the
load is completely taken off the axles and the weight is trans-
ferred to the stabilizer feet. This can result in personal injuries
and your tail lift, your vehicle, or the load can be damaged.



Set the air suspension control lever of your vehicle to po-
sition "Block"!

Betriebsanleitung_Hubladebuehnen_EN.book Seite 29 Donnerstag, 15. August 2019 4:04 16

«
...
27
28
29
30
31
...
»

Содержание MBB C 500 VAN





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBB C 500 VAN

Бренд: Samsung Страницы: 7

Бренд: Camtree Страницы: 2

Бренд: Camtree Страницы: 11

Бренд: Camtree Страницы: 4

Бренд: Jeep Страницы: 212

Бренд: YOKOGAWA Страницы: 12

Бренд: Wagan Страницы: 12

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 2

Бренд: quadient Страницы: 2

AcousticDesign AD-S52

Бренд: QSC Страницы: 4

Бренд: RAM Commercial Страницы: 12

Бренд: Xerox Страницы: 13

Бренд: Xerox Страницы: 41

Бренд: Öhlins Страницы: 8

prodrive SUR 3A00

Бренд: Öhlins Страницы: 4

Бренд: Öhlins Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды