Palfinger ILF 33 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 55

background image

ILF 33/44/55 Installation Manual

Rev 1.1

40

Main Power Connections

9.4

2GA. Liftgate
Power Cable

Aux.
Batteries

Liftgate
Mount Frame

Resetable
Circuit
Breaker

*In-Line
Fuse

Wires #2 and #4
go to postitive (+)

4-Conductor Control
Power Cable
from Control Board

***Ground

Wires #1 and Gr/Yl
go to ground (-)

Control Board
Location (Inside)

2GA. Liftgate
Power Cable

Main
Batteries

Liftgate
Mount Frame

**Resetable
Circuit
Breaker

*In-Line
Fuse

Wires #2 and #4
go to postitive (+)

4-Conductor Control
Power Cable
from Control Board

Wires #1 and Gr/Yl
go to ground (-)

Control Board
Location (Inside)

Ground

Battery Wiring Setup

– Truck

Battery Wiring Setup - Trailer

*In-Line ATC Fuse: 20 Amp.

Replace with same amperage fuse when necessary.

**Resettable Circuit Breaker: 150 Amp Min.

Replace with same amperage breaker when necessary.

***Ground: For optimal grounding, ground all batteries and power units to the body side rails of the vehicle.

NOTICE: DO NOT attempt to jump in-line fuses with other objects other than the specified fuse.
Do not increase the amperage rating of fuse. Serious harm to the liftgate will result when standard practices are not followed.

«
...
38
39
40
41
42
...
»

Содержание ILF 33
























































Отзывы:

Нет отзывов

Похожие инструкции для ILF 33

RDS17S-ELITE1-R1

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: National Instruments Страницы: 9

Air-Cooled Automatics ACAPTS-1.0

Бренд: Bernard Страницы: 4

Бренд: Telwin Страницы: 88

Бренд: Quickie Страницы: 108

Бренд: MONSTER MOBILE Страницы: 22

Бренд: Space Страницы: 96

Бренд: GYS Страницы: 40

PNOZ m ES CC-Link

Бренд: Pilz Страницы: 24

Бренд: Kühtreiber Страницы: 44

Torsion Add-on Version 3

Бренд: Instron Страницы: 32

Бренд: Miller Страницы: 136

Бренд: Lennox Страницы: 17

Бренд: Oshkosh Corporation Страницы: 92

JACKSHAFT MOTOR-CONTROL SYSTEM 815-RL

Бренд: Zap Страницы: 28

Бренд: Arc Machines Страницы: 22

Бренд: INVERTEC Страницы: 36

Бренд: BREWISTA Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды