background image

  The plastic wire ties are for looming and securing the wires to the vehicle.   

  The label sheet included is to identify each switch of its function. Simply peel off the 

label  needed and  place  it  under  the  switch wired  for  that  function.  The "R"  and "L" 
labels are for right and left in the event an on/off/on switch is turned sideways for turn 
signals 

 

 
 
 
 
 
 
 

Painless Performance Products LLC 

Limited Warranty and Return Policy 

 

Chassis  harnesses,  fuel  injection  harnesses,  and  switch  panel  units  are 

covered under a lifetime warranty.  
 

All other products manufactured and/or sold by Painless Performance are 

warranted  to  the  original  purchaser  to  be  free  from  defects  in  material  and 
workmanship  under  normal  use.  Painless  Performance  will  repair  or  replace 
defective products without charge during the first 12 months from the purchase 
date. No products will be considered for warranty without a copy of the purchase 

receipt showing the sellers name, address and date of purchase. You must return 
the product to the dealer you purchased it from to initiate warranty procedures.

Содержание 50340









Отзывы: