background image

3

Packard Bell Vibe 100 Disassembly Manual

Hazardous Voltage

There is hazardous voltage present inside the
MP3 player when it is connected to an AC
supply, even when the MP3 player’

s power

switch is off. Exposure to hazardous voltage
could cause personal injury. To avoid risk of
injury, contact an Authorized Service Provider
for proper (un)installation of optional
hardware devices.

Avoid Electrostatic Discharge

Electrostatic electricity can easily damage
circuit cards and integrated circuits (ICs). To
reduce risk of damage, store them in
protective packaging whenever they are not
installed in your system.

Add-in cards can be extremely sensitive to
ESD and always require careful handling.
After removing the card from the MP3 player,
place the card flat on a grounded, static-free
surface, component-side up. Use a
conductive foam pad if available, but not the
card wrapper. Do not slide the card over any
surface.

Before you install or remove memory
modules, video memory, disk drives, circuit
cards or other devices, protect them from
static electricity. To do so, make sure your
MP3 player’

s power switch is OFF. Then,

unplug the MP3 player’

s AC power cord.

Before picking up the device you (un)install,
you should wear an anti-static wrist wrap
(available at electronic supply stores). Be
sure to connect the wrist wrap to an
unpainted metal portion of the MP3 player
chassis. As an alternative, you can dissipate
electrostatic build-up by touching an
unpainted metal portion of the MP3 player
chassis with one hand. Then touch the device
you are (un)installing with the other hand, and
maintain continuous contact with it until it is
(un)installed in the MP3 player.

Power Supply Unit

Under no circumstances should you
attempt to disassemble the power
supply. The power supply contains
no user-serviceable parts. Inside the
power supply are hazardous
voltages that can cause serious
personal injury. Always return a
defective power supply to your
dealer.

WARNING

Ensure that the MP3 player is
disconnected from its power source
and from all telecommunications
links, networks, or modem lines
whenever the cover is removed. Do
not operate the MP3 player with the
cover removed.

AVERTISSEMENT

Assurez-vous que le lecteur MP3 est
débranché de son alimentation ainsi
que de toutes les liaisons de
télécommunication, des réseaux, et
des lignes de modem avant
d’

enlever le capot. Ne pas utiliser le

lecteur MP3 quand le capot est
enlevé.

WARNUNG

Der Player darf weder an eine
Stromquelle angeschlossen sein
noch eine Verbindung mit einer
Telekommunikationseinrichtung,
einem Netzwerk oder einer Modem-
Leitung haben, wenn die
Gehäuseabdeckung entfernt wird.
Nehmen Sie den Player nicht ohne
die Abdeckung in Betrieb.

ADVERTENCIA

Asegúrese de que cada vez que se
quite la cubierta del lector MP3, el
dispositivo haya sido desconectado
de la red de alimentación y de todos
lo enlaces de telecomunicaciones,
de red y de líneas de módem. No
ponga en funcionamiento el lector

Содержание Vibe 100












Отзывы: