PACIFIC CYCLE Mountain Bicycles; BMX Bicycles Скачать руководство пользователя | Manualshive

Страница: 86 / 119

background image

79

Some brakes have a special mechanism which enables you to set the
clearance on either side of the rim using a screwdriver. Brake pads
should finally be adjusted so that the leading edge of the pad makes
first contact with the rim. Some brakes have special curved washers
to allow this, but on less complex models it will be necessary to apply
a little force to the pad and its mounting.

Adjustment - Cantilever Calipers

Minor brake adjustment can be made via the barrel cable adjusters
which are located on each brake lever. To adjust, squeeze the brake
pads against the rim, loosen the lock nut, and turn the adjuster to pull
the brake pads closer to, or spread them away from the rim as required.
Brake pad clearance should be a maximum 2mm from the rim.
When correct, re-tighten the lock nut. If the pads cannot be set close
enough to the rim in this manner, you may have to adjust either the
length of the straddle cable or the length of the brake cable.

If the brakes use a separate brake cable and straddle cable, adjust
the straddle length by first screwing the barrel adjuster 3/4 of the way
in, then loosening the straddle cable fixing bolt, then pulling or pushing
the cable through the fixing bolt to adjust the length, and finally
re-tightening the fixing bolt.

Check that the straddle bridge is in the middle of the cable to ensure
even brake pad contact. Apply full force to the brake lever to test,
then fine tune using the barrel adjuster.

To adjust the brake cable length, loosen the brake cable fixing bolt on
the cable straddle bridge, adjust the length until the brake shoes are
the correct distance from the rim, then re-tighten and test.

Parallel

Parallel

Fully Adjustable Brake Shoes

Curved
Adjustment
Washer

Curved
Adjustment
Washer

2mm clearance

«
...
84
85
86
87
88
...
»

Содержание Mountain Bicycles; BMX Bicycles
























































































































Отзывы:

Нет отзывов

Похожие инструкции для Mountain Bicycles; BMX Bicycles

Бренд: Calira Страницы: 14

Ergopower Record 12s

Бренд: CAMPAGNOLO Страницы: 124

Бренд: CAMPAGNOLO Страницы: 100

Бренд: Dacor Страницы: 4

Бренд: NAKTO Страницы: 31

Бренд: quadient Страницы: 2

AcousticDesign AD-S52

Бренд: QSC Страницы: 4

Бренд: Wallbox Страницы: 7

Бренд: Xerox Страницы: 13

Бренд: Xerox Страницы: 41

Бренд: Aries Страницы: 3

Бренд: Yoshimura Страницы: 7

Бренд: Swann Страницы: 12

Бренд: Satlink Страницы: 16

Бренд: Filmcity Страницы: 9

Car Top Duffle Bag

Бренд: Rightline Gear Страницы: 2

Бренд: Fisher-Price Страницы: 12

Бренд: MELINERA Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды