manualshive.com logo in svg

Pacer S Series, Руководство по сборке, Страница: 7 / 7

Поделиться
Скачать
Pacer S Series Скачать руководство пользователя страница 7

7

Pump to Pedestal Assembly Procedures

A.  For pumps assembled to molded plastic pedestal assemblies  

 

 (Ref. 

#55/56).

 

1.  If utilizing the plastic shaft sleeve (Ref. #46) follow procedure #2  

 

 

found on page 3 of this assembly manual. (If the sleeve is not  

 

 

preapplied at the factory.

 

2.  For pedestals with carbon steel shafts (58-2053 01), install the  

 

 

slinger (Ref. #47) as per procedure 3/Fig. 6 on page 3. Do not  

 

 

install a slinger on pedestal assemblies which have stainless  

 

 

steel or titanium shaft sleeves.

 

3.  Place your pump bracket assembly onto the pedestal. Position  

 

 

the bracket with its handle opposite (180°) from the fl at, bottom  

  of 

the 

pedestal.

 

4.  Install an o-ring onto each 1½"/38mm long coarse threaded    

 

 

screw. Apply one large drop of Loctite #242 to the tips of the screw  

 

 

threads. Drop the screws through the four holes of the bracket  

 

 

and pedestal. Thread four kep nuts (Ref. #33) onto the screws.  

 

 

Tighten the screws and nuts using a large fl at head screwdriver  

 

 

and ½" socket wrench.

 

5.  Follow procedures 6-20 to complete your pump assembly.

B.  For pumps assembled to cast iron pedestal assemblies (Ref. #48)
 
 

1.  Do not install a plastic shaft sleeve (Ref. #46) or slinger (Ref. #47)  

 

 

onto your cast iron pedestal assembly.

 

2.  Place your bracket assembly onto the pedestal. Position the  

 

 

bracket with its handle opposite (180°) from the fl at bottom of  

  the 

pedestal.

 

3.  Follow procedures 5-20 to complete your pump assembly.

Bulletin no. 1732-01 7/16

Содержание S Series








Отзывы:

Нет отзывов