background image

PACE Sodr-X-Tractor Handpiece 

©2008 PACE Inc., Southern Pines, NC.  All Rights Reserved   

Page 11 of 11 

www.paceworldwide.com 

 
 
 
 
 
 
 

PACE Incorporated retains the right to make changes to specifications contained herein at 
any time, without notice.  Contact your local authorized PACE Distributor or PACE 
Incorporated to obtain the latest specifications.

 

 
The following are trademarks and/or service marks of PACE, Incorporated, MD, USA: 
 

INSTACAL

, FUMEFLO

, HEATWISE

, PACEWORLDWIDE

PERMAGROUND

, POWERPORT

, POWERMODULE

, TEMPWISE

, TIP-

BRITE

, AUTO-OFF

,

 

TEKLINK

, and INTELLIHEAT

 

 
The following are registered trademarks and/or service marks of PACE Incorporated, Annapolis 
Junction Maryland U.S.A.   
 

ARM-EVAC

®

, FLO-D-SODR

®

, MINIWAVE

®

, PACE

®

, SENSATEMP

®

, SNAP-

VAC

®

, SODRTEK

®

, SODR-X-TRACTOR

®

, THERMOFLO

®

, THERMOJET

®

THERMOTWEEZ

®

, VISIFILTER

®

, THERMO-DRIVE

®

, and TOOLNET

®

 
PACE products meet or exceed all applicable military and civilian EOS/ESD, temperature stability 
and other specifications including MIL STD 2000, ANSI/JSTD 001, IPC7711, and IPC A-610. 
 
Additional copies of this manual or other PACE literature may be obtained from: 

 
 
 
 
 
 

www.paceworldwide.com

 

 
 

PACE USA 

PACE Europe Limited 

9030 Junction Drive 

13 Tanners Drive Blakelands 

Annapolis Junction, MD  20701 

Milton Keynes 

USA MK145BU 
 United 

Kingdom 

 

 

 

Tel: 

(301) 490-9860 

Tel: 

(44) 01908-277666 

 

 

 

Fax: 

(301) 498-3252 

Fax: 

(44) 01908-277777 

 

 
 

Содержание Sodr-X-Tractor SX-80












Отзывы: