background image

 
Initially, a Green LED will illuminate (at bottom of graph).  As the airflow rate decreases (as the filter(s) start 
to become clogged), LED’s will illuminate high on the graphical display. 
 
Illumination colors will darken to shades of Yellow and finally to Red as the illumination reaches the top 
of the graphical curve. 
 
When the first Red LED illuminates, it is indicating insufficient airflow.  Replacement of the filter(s) at this 
point is highly recommended.  Refer to “Filter Replacement”, page 12. 
 
If the last Red LED (at the upper right of the display) illuminates, an alarm will sound.  Immediately, turn 
the system power off (Power Switch) and change filters. 

 

Caution 

 
Overheating may occur and cause motor damage if the system is operated with completely 
clogged filters. 
 

 

Motor Compensation Feature 

 

The Arm-Evac 250 features intelligent pump flow sensors that increase the power to the motor as filters 
become blocked to assure peak performance.   

 

Maintenance 

 

 

General Tips: 

 

 

Before opening the Arm-Evac 250, always turn off the power source. 

 

Protect the Arm-Evac and accessories from dampness. 

 

Do not extract water vapor or steam. 

 

The Arm-Evac 250 must not be operated without filters.  Impurities in the extracted air can 
damage the motor pump. 

 

Do not allow the Arm-Evac 250 or ducting hoses to become blocked. 

 

Do not extract corrosive compounds without checking with PACE. 

 

Re-calibrate the Arm-Evac 250 whenever a filter change out or system configuration change 
occurs. 

 

Filter Replacement 

 
 

Pre-Filter 

 

 

This filter removes coarse particles from the air.  In general, the pre-filter must be changed on a 

 

monthly basis.  However, depending on your particular process, the filter may need to be 

 

changed more or less frequently.  A visual inspection on a weekly basis is recommended. 

 
 

Main Filters 

 
 

Fume Extraction Filters remove particulates from the air and capture noxious odors and gases.  

 

Depending on your particular process, the filter cartridge may need to be changed more or less 

 frequently. 
 

 

 

10

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Arm-Evac 250

















Отзывы: