Radio Replacement and
Steering Wheel Control Interface
for Toyota / Lexus / Scion Vehicles
TY1A-RS
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Pacific Accessory Corporation
Page 5
Rev: V4
Date:090519
Steering Wheel Controls (cont.)
Alpine
JVC
Kenwood /
Lightning Audio
Clarion /
Nakamichi
2-Wire
Resistive
Pioneer
Other *
Sony
Fusion
1
2
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
3
Mute
Mute
Mute
Mute
Mute
Mute
Mute
Mute
4
Source
Source
Source
Source
5
Preset -
Track +
Play
Preset -
Preset -
Preset -
Track +
6
Source
Track -
Track +
Search -
Source
Source
Source / End Call
Track -
7
Track +
Band / Disc +
Track -
Band
Track +
Track +
Track +
Audio
8
Track -
Preset / Disc -
Disc / FM +
Send / End
Track -
Track -
Track -
Power
9
Power
Select
Disc / AM -
Send
Band
Band
Band
10
Enter / Play
Attenuation
Answer
End
Phone Menu Answer **
Power / End Call
11
Band / Program Phone Receive
Voice Dial
VR
Answer Call
End **
Voice Dial / Answer / End Call
12
Receive
Phone Reject
On Hook
End Call
PTT **
VR (Android Auto & Car Play)
Answer / End Call***
13
End
Voice Dial
Off Hook
VR
14
VR
Power
Mute
15
No specific
programming
order. Please
refer to the
owners manual
of your particular
radio for
programming
instructions..
* Advent, Boyo, Dual, Lightning Audio, Jensen, Rockford Fosgate & Visteon ** Jensen & Advent ONLY ***
XAV-AX100 Only
Please Note: On any entry with multiple commands, the commands shown are source dependent.
Optional Programming Order
SWC Re-Calibration Procedure
1. Turn the key to the ignition position.
2. Press and hold the programming button until the LED begins blinking amber.
When the LED begins blinking, release the programming button. The LED will
light solid amber.
3. Within 7 seconds, press and hold the button that is to be learned on the steering
wheel. The LED will turn off when the button is pressed and begin blinking when
the value has been learned. Once the LED begins blinking, release the button.
Please Note: the buttons must be calibrated in the order shown in the chart.
If you press the wrong button the LED will not respond at all.
4. If you need to program more buttons, repeat step 3 for each additional audio
function on the steering wheel.
5. If you come across a function in the chart that your steering wheel does not
have, press and release the program button on the side of the interface to skip
that function.
6. Once programming is completed, wait seven seconds. The LED will flash
indicating end of programming.
7. Test the interface for proper functionality. Whenever a SWC is pressed the LED on
the interface should blink. If any function does not work, repeat the programming
steps.
Re
‐
Calibration
Programming
Order
Volume Up
Volume Down
Seek Up
Seek Down
Mode
Voice
Phone Answer
Phone Hang Up
Enter
Back
Arrow Right
Arrow Left
After you have re-calibrated the SWC buttons, the default SWC button assignments will be the same as what is listed in the
chart on page 4. If you wish to re-assign button functions you must also go through the programming listed above (Optional
SWC Programing Procedure).
Optional SWC Programming Procedure
1
.
Turn the key to the ignition position.
2
.
Press and release programming button on the side of the interface. The Status LED will turn green.
3
.
Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn red when the button is pressed.
At this point you have two options:
D.
For short press functionality:
Release the button within 1.5 seconds. The LED will turn back on.
E.
For long press functionality:
Hold the button until the LED starts blinking. Release the button and the LED will
go back to solid.
4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function.
6. Once programming is completed, wait seven seconds. The LED will flash three times indicating end of programming.
7. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function
does not work, repeat the programming steps.
