
Pacific Accessory Corporation
Radio Replacement & Steering Wheel Control Interface
with OnStar Retention for General Motors Vehicles
RP5-GM11
Rev. 092117
Page 3
© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Optional Steering Wheel Control Programming
Alpine
JVC
Kenwood
Clarion
Other
Pioneer
Sony
Fusion
1
2
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
3
Mute
Mute
Mute
Mute
Mute
Mute
Mute
Mute
4
Source
Source
Source
Source
5
Preset -
Track +
Play
Preset -
Preset -
Preset -
Track +
6
Source
Track -
Track +
Search -
Source
Source
Source
Track -
7
Track +
Band / Disc +
Track -
Band
Track +
Track +
Track +
Audio
8
Track -
Preset / Disc -
Disc / FM +
Send / End
Track -
Track -
Track -
Power
9
Power
Select
Disc / AM -
Send
Band
Band
Band
10
Enter/Play
Attenuation
Answer
End
Answer
Phone Menu
Reject Call / Source
(Bluetooth
equipped radios
only)
11
Band / Program
Phone Receive
Voice Dial
VR
End
Answer Call
Answer / End Call
12
Receive
Phone Reject
On Hook
PTT
End Call
13
End
Voice Dial
Off Hook
VR
14
VR
Power
Mute (Multimedia
units only)
15
- Advent, Boyo, Dual, Lightning Audio, Jensen, Rockford Fosgate & Visteon
- Jensen & Advent ONLY
Optional Programming Order
Programming
1. Turn the key to the ignition position.
2. Press and release programming button on the side of the interface.
3.
Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn off when the button is pressed.
4.
If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
5.
If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function.
6.
Once programming is completed, wait seven seconds. The LED will flash three times indicating end of programming.
7. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function
does not work, repeat the programming steps
If you wish to re-assign the SWC functions the interface must be programmed in the specific order shown on the chart below. If
you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release
the programming button on the side of the interface to skip that function. The LED will flash off and on confirming that you have
successfully skipped that function and are ready to proceed to the next one.
Testing and Verification
1. Turn the ignition on. The LED on the interface will turn on and the +12v accessory wire will turn on.
2. Turn on the radio and check balance and fade. Note:
Premium Factory amplified Systems
will not fade as neither the
aftermarket radio or the RP interface have the ability to control the amplifier’s fader.
3.
Verify that the factory subwoofer (if present) is playing
4. Verify that all SWC are functioning properly for both the aftermarket radio and OnStar. To adjust OnStar volume, press the
OnStar button on the mirror then use the volume buttons on the SWC to adjust the level. The volume will raise a total of 8
times before returning to the original level.
5. Pressing the OnStar button on the rearview mirror will turn off the rear speakers and allow the OnStar audio to be heard in
the two front speakers. The OnStar active LED will also turn on. When OnStar disconnects, the radio will un-mute or turn
back on and the OnStar LED will turn off. Pressing the Mute/OnStar button on the steering wheel for 1.5 seconds will also
activate Onstar.
6. Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes or until the drivers door is opened.