INSTRUCTIONS AND PARTS LIST TG-TALON
TG TALON – Airbrush
Double Action - Internal Mix - Gravity Feed -
PTFE Packings.
WARNING:
Spray materials may be harmful if
inhaled or allowed to come into contact with the
skin or eyes. Consult the product label and material
safety data sheet supplied for the spray material.
Follow all safety precautions.
CAUTION:
Well
Ventilated Area Required to remove fumes, dust or
overspray.
Maximum Air Pressure 75 P.S.I.
TG Specifications:
• Dual Action • Gravity Feed • Internal Mox • Cutaway Handle w/ Pre-set Needle Stop • PTFE Packing
Options for Talon:
.25mm head (TT-1, TN-1 and TA-1) - Great for jobs requiring the extremely fine detail
.66mm head (TT-3, TN-3 and TA-3) - Great for spraying Metallics, Pearlescent and Thicker Paints
.66mm Fan Aircap (TAF-3, TN-3 and TT-3) Will give a 2-1/2 to 3 inch flat pattern
Working Pressures:
• Operating pressures 15-55 PSI; Maximum pressure 85 PSI. Fan aircap needs 20 PSI or more.
• 20-30 PSI is best for detail spraying w/ properly thinned paint
• Use the higher pressures for thicker material where fine detail is not critical or thin the paint to allow
lower pressures.
Equipment Set-up:
The Airbrush is held in the same manner as a pen, with index finger comfortably over the finger button.
1. Attach air hose to air supply and to airbrush. If using a regulator set pressure between 20 -55 PSI.
Airbrush Operation:
1. Press down on Finger Button to release air and pull back on button to control quantity of color.
2. To spray a fine line without heavy ends, start moving the airbrush without release of color. Then start
the color at the beginning of line and stop the color at the end, but continue the motion of the airbrush
after the color has stopped.
3. Practice this movement until you can spray a fine line or a broad pattern without heavy build up at
the beginning or end of your strokes.
4. Speed of movement controls density of color and fading effects at beginning and end of strokes.
5. For detail, hold the airbrush very close to the surface push down for air and pull back very slowly on
the Finger Button to release a small amount of paint.
6. For background work and broad effects, hold the airbrush away from the work surface and pull back
on Finger Button to release required amount of color.
7. For Stippling remove the aircap, push down on the trigger and pump the trigger forward and back.
Adjust the air pressure between 15 and 50 PSI for desired stipple effect.
NO. PART
DESCRIPTION
1.
TAL-23
Crown Cap
1a.
TAF-3
Fan Aircap for .66mm head -
*2.
TA-1
,
TA-2
,
TA-3
Aircap (.25mm, .38mm, .66mm)
*3.
TT-1
,
TT-2
,
TT-3
Tip (.25mm, .38mm, .66mm)
4.
MIL-12
“O” Ring for TG-30 Shell
5.
TG-30
Shell Assembly
6.
TG-4
Cup Cover
7.
TAL-8
Packing Assembly PTFE
8.
TAL-37
Trigger
9.
TAL-14
Valve Casing
10.
TAL-36
Valve Plunger (Includes O-ring)
11.
TAL-15
Valve Adapter (Includes O-ring)
12.
A-22
Spring
17.
TAL-18
Rocker Assembly
18.
MIL-11
Needle Spring
19.
TAL-17
Spring Housing
20.
TAL-19
Needle Lock Nut
21.
MIL-12
“O” Ring for TG-34 Handle
22.
TAL-34
Handle & Stop Assembly
23.
3A-4
“O” Ring
*24.
TN-1
,
TN-2
,
TN-3
Needle (.25mm, .38mm, .66mm)
25.
TAL-35
Allen Wrench
26.
TAL-28
Wrench
*Note: Etch lines on Items 2.,3.
and 24. indicate size.
All should match when installed
on airbrush.
