Tube Replacement
Commercial Glueboard Insect Control
Starter Replacement
SPECIFICATION / REPLACEMENT PARTS
Unit
PL30 White
Voltage
230V ~ 50Hz
Dimensions(mm)
470 x 285 x 90
Coverage
80 Sq. Meters
Weight
4 Kg
Light Output
30W
Tubes
2 x I616
Starter
2 x I154
Glueboards (x6)
INF209
Unit
PL60 S/S
Voltage
230V ~ 50Hz
Dimensions(mm)
470 x 330 x 130
Coverage
80 Sq. Meters
Weight
7 Kg
Light Output
60W
Tubes
4 x I616
Starter
4 x I154
Glueboards (x6)
INF209
GLUEBOARD REPLACEMENT
BEFORE REPLACING THE GLUEBOARD, ALWAYS ENSURE THAT THE UNIT IS DISCONNECTED FROM THE
MAINS SUPPLY.
The glueboard should be replaced every month with a genuine glupac
™
glueboard.
Use of non-approved glueboards may invalidate your guarantee.
To replace the glueboard…
PlusLight
™
30
1. Remove the mains cable from your
PlusLight
™
.
2. Swing open the front guard untill it rests open against the fixing surface.
3. Remove the used glupac
™
glueboard by simply releasing from the metal
chassis and either retain for catch evaluation or dispose of it hygienically.
4. Remove the protective release paper from the new glupac
™
glueboard.
5. Carefuly position the new glupac
™
glueboard into position with the adhesive
side facing the tubes, ensuring the glueboard is held in position by the metal
clips at the top of the metal chassis.
PlusLight
™
60
1. Swing open the front guard untill it is held in position by the aluminium clips.
2. Remove the used glupac
™
glueboard by simply releasing from the metal
chassis and either retain for catch evaluation or dispose of it hygienically.
3. Remove the protective release paper from the new glupac
™
glueboard.
4. Carefuly position the new glupac
™
glueboard into position with the adhesive side
facing the tubes, ensuring the glueboard is held in position by the metal clips at the
top of the metal chassis.
5. Release the front guard by pulling the aluminium cilps away from the chassis.
Always ensure the selected genuine glupac
™
glueboards are compatible with your unit, available
from your PCO or P+L Systems Ltd.
TUBE REPLACEMENT
BEFORE REPLACING THE TUBES, ALWAYS ENSURE THAT THE UNIT IS DISCONNECTED FROM THE MAINS SUPPLY.
To ensure the efficiency of
PlusLight
™
in catching flying insects, the UV tubes should be replaced
annually. After twelve months the phosphor coating that emits the correct wavelength of UV
light has burnt away and the UV output is diminished substantially.
To replace the UV tubes…
1. Rotate the tube through 90°, freeing it from the tube holders.
2. Pull the tube away from the chassis.
3. Dispose of the used UV tube in conjunction with local WEEE regulations.
STARTER REPLACEMENT
BEFORE REPLACING THE STARTERS, ALWAYS ENSURE THAT THE UNIT IS DISCONNECTED FROM THE MAINS SUPPLY.
The starters provide an extra spark to initially light the UV tube. Starters wear out and should be
replaced at the same intervals as the UV tubes.
To replace the starters…
1. Rotate the starter anti-clockwise.
2. Pull the starter free from the unit.
Glueboard Replacement
C
2008
P+L Systems Ltd
Information provided on these instructions is modified and
updated from time to time. This is due to the constant
redevelopment of our products. As such, it is not intended that
you should rely on it or that it should form part of any contract.
P+L Systems Ltd
Ten St James Business Park
Grimbald Crag Court
Knaresborough
HG5 8QB UK
T +44 (0)800 988 5359
F +44 (0)1423 863 497
W www.pandlsystems.com
E [email protected]
R2 04/08
