P.I.T. PSW400-C, Руководство по эксплуатации

Страница: 4 / 16

Clean Water Pump
3
are prohibited.
► It is forbidden to pump explosive, fl am-
mable, corrosive or health hazardous
substances, as well as water containing
mechanical impurities in the form of
sand, stones, etc.
► The pump is not suitable for pumping
chlorine-containing water in swimming
pools.
► Not recommended for pumping drink-
ing water.
► When starting the pump for the first
time, ensure that it is completely fi lled
with water. it is not allowed to operate
the pump without water consumption.
► Air entering the suction line is not al-
lowed.
► To avoid freezing, the water must be
completely drained from the pump and
from the suction and pressure lines.
Product Description and Specifi-
cations
Read all the safety and general in-
structions.
Failure to observe the safety and general
instructions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the begin-
ning of this operating manual.
Intended use
Submersible drainage pump is designed to
pump only clean fresh water. It can be used
for pumping water from reservoirs, organizing
water intake from a depth (wells) and supply-
ing it to a height, to protect basements and
other premises from fl ooding; for drainage of
reservoirs, reservoirs, pits and use in aeration
and drainage systems, taking into account the
technical characteristics of the model.
The product is not intended for continuous
operation (continuous pumping mode).
Product Features
The numbering of the product features refers
to the diagram of the power tool on the graph-
ics page.
1.Pump casing
2.Handle for carrying the pump
3.Float switch
4.Telescopic boom
5. Shut-off valve
6.Nutzer
Technical Data
Model PSW400-C
Rated voltage 220 V~/50 Hz
Model PSW400-C
Rated power 400 W
Max. fl ow 6 m³/h
Max.head 11м
Outlet diameter Ø25 mm
Weight 4,75 Kg
Contents of delivery
Submersible drainage pump 1 pc
Float switch 1 pc
Rod with fl exible spout 1 pc
Shut-off valve 1 pc
Outlet nipple 1 pc
Instruction manual 1 pc
Note
Text and numbers may contain technical er-
rors and typographical errors.
Since the product is constantly being im-
proved, P.I.T. reserves the right to make
changes to the specifications and product
specifi cations specifi ed here without prior no-
tice.
Installation
► Check the power cable for damage, if
found, contact an authorized service cen-
ter for replacement. Make sure that the
parameters of the power supply network
correspond to those indicated in the table,
otherwise the pump will not be able to per-
form its functions in full or may fail.
► Make sure the outlet line or hose is clear,
not clogged or pinched before use. Check
and if necessary clean the water intake of
the pump.
► Screw on the supplied L-shaped outlet.
A flexible hose can be connected to the
branch pipe. Please note that the pump
performance depends on the diameter of
the hose, the smaller the diameter of the
connected hose, the lower the pump per-
formance. The minimum permissible diam-
eter of the connected hose is 25 mm.
► Adjust the length of the fl oat switch wire by
attaching the wire to the hole in the pump
body. This allows you to adjust the immer-
sion depth and the automatic cut-off depth.
If the water level falls below the level of
the float switch, the pump will shut off.
This protects the pump from running dry.
The float switch can be forcibly locked in
order to pump out liquid to the level of the
water intake holes. Fasten the fl oat switch
vertically in the slots on the pump housing.
Make sure that the intake holes are always
covered with water. Otherwise, if the water
F il