P.I.T. PSB13-C2, Руководство пользователя

Страница: 5 / 22

Impact Drill
04
tools are dangerous in the hands of untrained
users.
►
Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condition
that may aff ect the power tool’s operation.
If damaged, have the power tool repaired
before use.
Many accidents are caused by
poorly maintained power tools.
►
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
►
Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working con-
ditions and the work to be performed.
Use
of the power tool for operations diff erent from
those intended could result in a hazardous
situation.
Service
► Have your power tool serviced by a
qualifi ed repair person using only identical
replacement parts.
This will ensure that the
safety of the power tool is maintained.
bonded abrasives.
When carrying out abrasive cutting, use a
moderate feed that is suited to the material
being machined. Do not exert pressure on the
cutting disc and do not tilt or swing the power
tool.
Do not attempt to reduce the speed of a cut-
ting disc coming to a stop by applying pres-
sure from the side.
The power tool must always work in an
up-grinding motion. Otherwise, there is a risk
that it will be pushed uncontrolled out of the
cut. For best results when cutting profi les and
rectangular tubing, start at the smallest cross
section.
Safety Warnings for Drills
Safety instructions for all operations
► Use auxiliary handle(s), if supplied with
the tool. Loss of control can cause personal
injury.
►
Hold the power tool by insulated grip-
ping surfaces, when performing an oper-
ation where the cutting ac- cessory may
contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may
make ex- posed metal parts of the power tool
“live” and could give the operator an electric
shock.
Safety instructions when using long drill
bits
► Never operate at higher speed than the
maximum speed rating of the drill bit. At
higher speeds, the bit is likely to bend if al-
lowed to rotate freely without contact- ing the
workpiece, resulting in personal injury.
►
Always start drilling at low speed and
with the bit tip in contact with the work-
piece.
At higher speeds, the bit is likely to
bend if allowed to rotate freely without con-
tact- ing the workpiece, resulting in personal
injury.
►
Apply pressure only in direct line with
the bit and do not apply excessive pres-
sure.
Bits can bend causing breakage or loss
of control, resulting in personal injury.
Additional safety warnings
► Secure the workpiece. A workpiece
clamped with clamping devices or in a vice is
held more secure than by hand.
►
Switch the power tool off immediately
if the application tool becomes blocked.
Be prepared for high torque reactions
which cause kickback.
The application tool
becomes blocked when it becomes jammed
in the workpiece or when the power tool be-
comes overloaded.
►
Use suitable detectors to determine if
utility lines are hidden in the work area
or call the local utility company for assis-
tance.
Contact with electric lines can lead to
fi re and electric shock. Damaging a gas line
can lead to explosion. Penetrating a water
line causes property dam- age or may cause
an electric shock.
►
Always wait until the power tool has
come to a complete stop before placing
it down.
The application tool can jam and
cause you to lose control of the power tool.
Product Description and Specifi-
cations
Read all the safety and general
instructions. Failure to observe the safety
and general instructions may result in electric
shock, fi re and/or serious injury.
Please observe the illustrations at the begin-
ning of this oper- ating manual.
Intended Use
The power tool is intended for impact drilling
in brick, con- crete and stone, as well as for
drilling in wood, metal, ceramic and plastic.
Tools with electronic control and right/ left
rotation are also suitable for screwdriving and
thread cutting.