background image

Electric Hammer Drill

6

To change the operating mode, press the 

release button and turn the drilling/hammer 

drilling selector switch to the desired position 
until it can be heard to latch. 

Position for hammer

 drilling in 

concrete or stone

Position for drilling

 without impact 

in wood, metal, ceramic and plastic 
as well as for screwdriving

Vario-Lock position

 for adjustment 

of the chiselling position The mode 
selector switch does not latch in this 

position.

Position for chiselling

Reversing the rotational direction

The rotational direction switch is used to re-
verse the rotational direction of the machine. 

However, this is not possible with the On/Off 

switch actuated.

Switching On and Off

To start the machine, press the On/Off switch.

To lock the On/Off switch, keep it pressed and 

additionally push the lock-on button.

To switch off the machine, release the On/

Off switch. When the On/Off switch is locked, 

press it first and then release it.

Setting the Speed/Impact Rate

The speed/impact rate of the switched on 

power tool can be variably adjusted, depend-

ing on how far the On/Off switch is pressed. 

Light pressure on the On/Off switch results in 

low speed/impact rate. Further pressure on 

the switch increases the speed/impact rate.

Overload Clutch

 

If the tool insert becomes caught or 
jammed, the drive to the drill spindle is 
interrupted. 

Because of the forces that 

occur, always hold the power tool firmly 
with both hands and provide for a secure 
stance.

 

If the power tool jams, switch the ma-
chine off and loosen the tool insert.

 

When switching the machine on with the 
drilling tool jammed, high reaction torques 
can occur.

Working Advice

 

Before any work on the machine itself, 
pull the mains plug.

Changing the Chiselling Position (Vario-Lock)

 

-

Changing the Chiselling Position (Vario-

-   Tighten the depth gauge lock.

Inserting SDS-plus Drilling Tools (see fig

-

ure C)

The SDS-plus drill chuck allows for simple 
and convenient changing of drilling tools with-
out the use of additional tools.

 

-

Clean and lightly grease the shank end of 
the tool.

 

-

Insert the tool in a twisting manner into the 
tool holder until it latches itself.

 

-

Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus 
drilling tool can move freely. This causes a 
certain radial run-out at no-load,

which has no effect on the accuracy of the drill 

hole, as the drill bit centres itself upon drilling.

Removing SDS-plus Drilling Tools (see fig

-

ure D)

 

-

Push back the locking sleeve and remove 
the tool.

Dust Extraction with the Dust Extraction 
Attachment

 

Dust from materials such as lead-con-
taining coatings, some wood types, 
minerals and metal can be harmful to 

one’s health.

 Touching or breathing-in the 

dust can cause allergic reactions and/or 

lead to respiratory infections of the user or 
bystanders. 

Certain dust, such as oak or beech dust, 
is considered carcinogenic, especially in 
connection with wood-treatment additives 
(chromate, wood preservative). Materials 
containing asbestos may only be worked by 
specialists.

 

-

As far as possible, use a dust extraction 
system suitable for the material.

 

-

Provide for good ventilation of the working 
place.

 

-

It is recommended to wear a P2 filter-class 

respirator.

Observe the relevant regulations in your 
country for the materials to be worked.

 

Prevent dust accumulation at the work-
place. Dust can easily ignite.

Operation

Starting Operation

 

Observe correct mains voltage! The 
voltage of the power source must agree 

with the voltage specified on the name

-

plate of the machine.

Setting the operating mode 

With the selector switch for drilling/hammer 

drilling, the operating mode of the machine is 
selected.

Содержание PBH24-C2























Отзывы: