WARNING:
BEFORE CLEANING YOUR CHAINSAW OR
CARRYING OUT ANY MAINTENANCE PROCEDURE,
MAKE SURE THE BATTERY REMOVED TO PREVENT
ACCIDENTAL STARTING.
CAUTION:
ALWAYS WEAR GLOVES WHEN HANDLING
THE CHAIN AS IT IS VERY SHARP AND CAN CUT YOU
WHEN IT IS NOT MOVING.
MAINTENANCE
TROUBLESHOOTING
Battery protection system
The tool is equipped with the battery protection system, which helps to ensure a long service
life.
The output power automatically cuts off during operation when the tool and/or battery are
placed under the following situations:
• When the tool is overloaded:
If this occurs, release the trigger switch and remove causes of overload, then pull the
switch trigger again to restart.
• When the remaining battery capacity becomes low:
Recharge the battery pack.
Note:
The battery protection system does not in any way damage the tool.
Note:
The indicated capacity may be lower than the actual level during use or immediately
after using the tool.
Adjusting the Chain Tension
1.
Loosen the guide bar locking knob
slightly, by rotating it in an anti clockwise
direction.
2. Adjustment chain tension screw
CLOCKWISE to increase chain tension.
Turning screw COUNTERCLOCKWISE will
decrease amount of tension on the chain.
Adjust the chain tension screw for the
correct tension.
3 - 4mm gap is
the ideal tension
For the correct chain tension, pull up on the
chain from the top and middle of the exposed
guide bar. The bottom tip of the links should
only just stay in the track.
3. After the chain has been accurately
tensioned, lock the guide bar in place with
the guide bar locking knob.
Note:
Proper tension of the chain is extremely important and must be checked before
starting, as well as during any cutting operation. Taking the time to make
adjustments to the chain will result in improved cutting performance and
prolonged chain life.
Maintaining the guide bar
1. Remove any sawdust from the guide bar, including the groove.
Oil and sawdust combine and emit a burning smell during operation if the blade is not
regularly cleaned.
2. Make sure that the oil port is not clogged. Grease the nose sprocket at the tip of the
guide bar.
3. Check for oil leakage and loose fastenings, especially those securing the handles and
the guide bar.
4.
Reverse the guide bar every 8 working hours to ensure uniform wear. Check the guide
rails frequently and if necessary remove burrs and square up the rails using a flat file.
Chain Sharpening
Chain File: 3.96mm (5/32”)
Chain Pitch: 9.53mm (3/8”)
Chain Gauge: 1.1mm (0.043”)
Sharpen the chain regularly to maintain
optimum performance of the saw. Signs of a
dull chain are:
• The sawdust becomes powder-like
• Extra force is required to execute a cut
• The cut does not track in a straight line
• Increased vibration
Sharpen each cutter using a round 3.96mm (5/32”) chain file. Keep the file level with the
top plate of the tooth. Always use outward strokes and maintain a 30° angle between the
chain and file. After sharpening, the cutters must all have the same width and length.
After every 3–4 uses get an authorised repair centre to professionally sharpen your chain.
They have the special tools necessary to ensure the correct cutting angles and depths.
LEFT HAND
CUTTERS
STRAIGHT
ARM
POSITION
CHAIN
LINE
RIGHT HAND
CUTTERS
30°
30°
Cleaning and storing
• Keep the handles free of grease so that you can maintain a firm grip.
• Clean the device as required with a damp cloth and, if necessary, mild washing up
liquid.
• If the chainsaw is not to be used for an extended period of time
then you should remove the chain oil from the tank. Briefly immerse the chain and
the cutter rail in an oil bath and then wrap them
in oil paper.
• Ensure that the guide bar cover is in place when storing.
CAUTION!
ALWAYS DISCONNECT THE BATTERY BEFORE
CLEANING THE CHAINSAW.
CAUTION!
NEVER IMMERSE THE UNIT IN WATER OR
OTHER LIQUIDS IN ORDER TO CLEAN IT.
CAUTION!
STORE THE CHAINSAW IN A SAFE AND DRY
PLACE OUT OF THE REACH OF CHILDREN.
LED lights do not illuminate on charger
Check the charging adaptor is securely plugged into the wall outlet.
Check the battery is firmly connected to the charging cradle.
Check that the charging jack is securely connected to the charging cradle.
The battery has a short run time
Ensure the battery is properly charged. It will take 4-5 charging cycles before the battery
reaches optimum charge and run time.
Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents. This is normal and
does not indicate a problem.
