KNOW YOUR PRODUCT
SETUP & PREPARATION
PXCBLVS-018U
1. ASSEMBLY
3. INSERTING & REMOVING THE BATTERIES
4. CONTROLS
5. USING THE BLOWER VAC
OPERATION
2. BATTERY & CHARGING
(SOLD SEPARATELY)
1. Guide Wheels
2. Lower Tubes
3. Upper Tubes
4. Auxiliary Handle
5. Shoulder Strap Hook
6. Variable Speed Dial
7. On/Off Trigger
8. Collection Bag
9. Mode Selector
10. Battery Seating
11. Main Handle
Brushless Blower Vac
1
2
3
4
5 6
7
8
BATTERY & CHARGER (sold separately)
This tool is compatible with all battery and chargers from the Ozito
Power X Change Range.
CAUTION:
THE CHARGER FOR THIS PRODUCT
SHOULD BE PROTECTED BY A RESIDUAL CURRENT
DEVICE (RATED AT 30mA OR LESS).
The purchased battery will be shipped in a low charge condition, and requires charging
prior to use. Allow several cycles of charging and discharging (through use of the tool)
for the battery to reach its optimum performance / runtime.
1. Connect the charger into a mains power outlet.
4. The charger LED will illuminate
red signifying that the battery is
charging.
3. With the charger sitting on a flat
surface, align the raised ribs on
the battery with the recess in the
charger and slide onto the charger
ensuring a firm connection.
2. The charger LED will flash green
showing power is being supplied
to the charger.
5. The charger LED will illuminate
green once the battery is charged.
Charging your lithium ion battery - Fast Charger
Charger LED Indicator
LED Indicator
Situation
GREEN (Flashing)
Stand By (no battery pack is inserted).
RED (Flashing)
Battery is charging (low charge).
RED (Illuminated)
Battery is charging (mid charge).
GREEN (Illuminated)
Battery is 85% - 100% charged and ready for use.
BOTH(Illuminated)
Battery pack is too hot or too cold (charging will begin
automatically when battery reaches correct charging
temperature).
BOTH (Flashing)
Defective battery. Never charge a defective battery
pack!
Remove battery pack from charger.
Battery Charge Indicator
The purchased battery is equipped with a
battery charge indicator to show the state of
the battery charge.
Press the charge indicator button and look to
see which LED lights.
Battery requires
immediate charging.
Low state of charge, requires charging soon.
Mid state of charge.
Full state of charge.
Note:
The battery needs to be removed from the tool to check the state of charge.
1. Connect the charger into a mains power outlet.
4. The charger LED will illuminate red signifying that the battery is charging.
3. With the battery sitting on a flat
surface, align the raised ribs on the
battery with the recess in the charger
and slide onto the battery ensuring a
firm connection.
2. The charger LED will flash green
showing power is being supplied
to the charger.
5. When removing the charger from the
battery, first press the battery release
tab, then slide the charger from its
position.
Charging your lithium ion battery - Eco Charger
Charger LED Indicator
LED Indicator
Situation
GREEN (Flashing)
Stand By (no battery pack is inserted).
RED (Illuminated)
Battery is charging (low charge).
GREEN (Illuminated)
Battery is charged and ready for use.
RED (Flashing)
Battery or Charger fault.
RED & GREEN (Flashing)
Battery pack is too hot or too cold (remove battery from
charger and store at room temperature 20ºC. Insert
battery again when at correct charging temperature). If
this happens again, the battery is defective and needs
to be replaced.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
APPLICATIONS
ACCESSORIES
12. Shoulder Strap
13.
Assembly Screws 1 x 16mm,
2 x 50mm long.
12
13
10 11
9
STOP
STOP
1. Slide two batteries of the
same capacity and same
charge state into the rear
of the blower vac aligning
the ribs so that they click
into place.
Removing the Batteries from the Blower Vac
1. Press and hold the battery
release tab to release
a battery and slide the
battery out.
Inserting the Batteries into the Blower Vac
On/Off Trigger
1. Squeeze the on/off trigger to
start. Motor will start after a
short delay.
2. To stop operation, release the
on/off trigger.
Variable Speed Dial
1. To achieve the greatest flow of
air, move the dial to the “MAX”
setting.
2. To lower the air speed rotate the
variable speed dial to a lower
speed, or “MIN” setting.
Mode Selector
1. To select the blower function
turn the dial right to the blower
icon.
2. To select the vacuum / mulching
function turn the dial left to the
vacuuming icon.
1. Make sure the collection bag is
attached and zipped up correctly.
2. Make sure two batteries of the
same capacity and same charge
state are inserted into the blower
vac.
3. Select the desired operation
mode.
4. Set the variable speed dial to the
desired air speed.
5. Turn on by squeezing the On/Off
Trigger.
Emptying the Collection Bag
1. Open the zip at the rear of the
bag.
2. Be sure to close the zip prior to
operating the blower vac.
The flow of air can be regulated by turning the variable speed dial.
CAUTION:
ENSURE THE TOOL IS OFF & THE BATTERY
REMOVED BEFORE PERFORMING ANY OF THE FOLLOWING
OPERATIONS.
CAUTION:
ENSURE THE TOOL IS OFF & THE BATTERY
REMOVED. WAIT UNTIL THE IMPELLOR HAS STOPPED
BEFORE ATTEMPTING TO EMPTY OR REMOVE THE
COLLECTION BAG.
Assembling the Tubes
1. Place the lower tube onto the
upper tube.
2. Secure the tubes together with
supplied 50mm long security
screw using a flat tip screwdriver
(not included).
Note:
Once installed the security screw cannot be removed.
STOP
STOP
3. Feed the top of the assembled
tubes into the motor housing. Push
together until they are connected
firmly.
4. Secure in place with the
remaining 50mm long security
screw.
STOP
5. Slide the wheel support over the
lower tube as far as the stop.
6. Secure with the supplied 16mm
long screw using cross tip
screwdriver (not included).
Attaching the Collection Bag
2. Attach the plastic connector on
the collection bag to the outlet
in the motor housing. Ensure the
tab clicks into the hole of the
connector.
1. Attach the clip on the collection
bag to the hook underneath the
upper tube.
3. Place the plastic connector on the
collection bag to the hook on the
motor housing.
Fitting the Shoulder Strap
1. Unscrew the knurled nut on the
shoulder strap hook and place
the strap through the gap.
2. Re-tighten the knurled nut on the
shoulder strap hook and adjust
the length as required.
Note:
To use the shoulder strap simply slide the strap over your shoulder
so that some of the weight of the blower vac can be taken by your
shoulder.
Note:
Always use 2 batteries of the same capacity and same charge state
with the blower vac.
7. Place both wheels onto either side of the bracket, push to lock in place.
STOP
Attaching the Auxiliary Handle
1. Place the handle over the motor
housing so it is positioned
correctly.
2. Insert the bolt and secure turning
clockwise. Do not overtighten.
M
IN
M
AX
M
IN
Note:
Batteries can be easily removed and inserted with the collection bag
fitted.
STOP
