Ozito PXBPS-254 Скачать руководство пользователя страница 3

Battery Charge Indicator

The purchased battery is equipped with a 
battery charge indicator to show the state of 
the battery charge.
Press the charge indicator button and look to 
see which LED lights.

Battery requires 
immediate charging

Low state of charge, requires charging soon.

Mid state of charge

Full state of charge.

Note:

 The battery needs to be removed from the tool to check the state of charge. 

1    Connect the charger into a mains power outlet.

4  The charger LED will illuminate red signifying that the battery is charging.

3   With the battery sitting on a flat 

surface, align the raised ribs on the 

battery with the recess in the charger 

and slide onto the battery ensuring a 

firm connection.

2   The charger LED will flash green 

showing power is being supplied 

to the charger.

5  When removing the charger from the 

battery, first press the battery release 

tab, then slide the charger from its 

position.

Charging your lithium ion battery - Eco Charger

Charger LED Indicator 

LED Indicator 

Situation

GREEN (Flashing) 

Stand By (no battery pack is inserted) 

RED (Illuminated)

Battery is charging (low charge)

GREEN (Illuminated)

Battery is fully charged

RED (Flashing)

Battery or Charger fault

RED & GREEN (Flashing)

Battery pack is too hot or too cold (remove battery from 
charger and store at room temperature 20ºC. Insert 
battery again when at correct charging temperature). If 
this happens again, the battery is defective and needs 
to be replaced.

2.  BATTERY & CHARGING 

(sold separately)

The purchased battery will be shipped in a low charge condition, and requires charging 
prior to use. Allow several cycles of charging and discharging (through use of the tool) 
for the battery to reach its optimum performance / runtime.

CAUTION:

 

THE CHARGER FOR THIS PRODUCT SHOULD 

BE PROTECTED BY A RESIDUAL CURRENT DEVICE 
(RATED AT 30mA OR LESS).

1    Connect the charger into a mains power outlet.

4  The charger LED will illuminate 

red signifying that the battery is 

charging.

3   With the charger sitting on a flat 

surface, align the raised ribs on 

the battery with the recess in the 

charger and slide onto the charger 

ensuring a firm connection.

2   The charger LED will flash green 

showing power is being supplied 

to the charger.

5  The charger LED will illuminate 

green once the battery is fully 

charged.

Charging your lithium ion battery - Fast Charger

Charger LED Indicator 

LED Indicator 

Situation

GREEN (Flashing) 

Stand By (no battery pack is inserted) 

RED (Flashing)

Battery is charging (low charge)

RED (Illuminated)

Battery is charging (mid charge)

GREEN (Illuminated)

Battery is fully charged

BOTH(Illuminated)

Battery pack is too hot or too cold (charging will begin 
automatically when battery reaches correct charging 
temperature).

BOTH (Flashing)

Defective battery. Never charge a defective battery 
pack!
Remove battery pack from charger.

Содержание PXBPS-254









Отзывы: