DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
TROUBLESHOOTING
Power tools that are no longer usable should not be disposed of with household
waste but in an environmentally friendly way. Please recycle where facilities exist.
Check with your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw materials. Reuse of
recycled material decreases pollution in the environment. Please recycle packaging
where facilities exist. Check with your local council authority for recycling advice.
Spare Part
Part No.
Battery pack 4.0Ah
PXBP-400
Fast charger
PXCG-030 or PXCFCH-030
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings Warehouse.
For further information, or any parts not listed here,
visit www.ozito.com.au or contact Ozito Customer
Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR
BATTERY CHARGER.
1.
Before using the charger read all instructions and cautionary markings on the charger, battery pack
and the product using the battery pack.
2.
This charger is not intended for any uses other than charging rechargeable batteries. Any other use
may result in risk of fire, electric shock or electrocution.
3.
Do not place any object on top of the charger or place the charger on a soft surface that may result in
excessive internal heat. Place the charger in a position away from any heat source.
4.
To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when
disconnecting the charger.
5.
Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected
to damage or stress.
6.
An extension cord should not be used unless absolutely necessary. Use of an improper extension cord
could result in the risk of fire, electric shock or electrocution.
7.
Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any
way. Have it checked by an electrician or power tool repairer.
8.
Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair is
required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
9.
To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning.
Removing the battery pack will not reduce this risk.
10.
Never attempt to connect 2 chargers together.
11.
DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed
40ºC (such as inside sheds or metal buildings in summer).
12.
The charger is designed to operate on standard household electrical power (240 volts). Do not attempt
to use it on any other voltage!
13.
The battery pack is not fully charged out of the carton. First read the safety instructions and then
follow the charging notes and procedures.
14.
The longest life and best performance can be obtained if the battery pack is charged when the air
temperature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below 10ºC or
above 40ºC. This is important and will prevent damage to the battery pack.
15.
Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery
can explode in a fire.
16.
Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or
cracks, immediately discontinue use and do not recharge.
17.
During charging, the battery must be placed in a well ventilated area.
BATTERY AND CHARGER SAFETY WARNINGS
Read instruction manual
Nm
Newton Meters
Always keep the lawnmower on the ground when mowing.
Tilting or lifting the lawnmower may cause stones to be thrown out.
Beware of servering toes or hands. Do not put hands or feet near
a rotating blade.
Do not mow in the rain or leave the lawnmower outdoors while raining.
Keep bystanders away. Do not mow whilst people especially children
or pets are in the mowing area.
Blade continues to rotate after the machine is switched off. Wait until all
machine components have completely stopped before touching them.
Pull out Safety Key before
carry out any repair work
Regulator compliance mark
Problem Cause
Remedy
Mower is not
starting
Possible clogging
Check underneath the mower and clear out
as necessary
Battery is low in charge
Charge battery
Battery not inserted
properly
Insert battery pack correctly
Grass too long
Raise the cutting height to reduce starting
load
Safety key not inserted
correctly
Fit correctly
Mower is
hard to push
Height of cut too low
Raise cutting height
Cutting blade blunt
Replace blade
Possible clogging
Check underneath the mower and clear out
as necessary
Grass too long
Raise the cutting height and walk slower
Grass too dense
Raise the cutting height and walk slower and
cut more frequently
Wet grass
Wait until the grass dries before mowing
Motor stops
while cutting
Height of cut too low
Raise the cutting height
Battery has no power
Charge battery
Mower is
not catching
grass properly
Height of cut too low
Raise the cutting height
Wet grass
Wait until the grass dries before mowing
Mower
vibrating
Bent or damaged blade
Replace blade
