manualshive.com logo in svg

Ozito OZJS400A, Инструкция по эксплуатации

Поделиться
Скачать
Ozito OZJS400A Скачать руководство пользователя страница 12

11

MAINTENANCE

DESCRIPTION OF SYMBOLS

  

V

     

Volts

 

              

Hz

     

Hertz

  

~

     

Alternating current             

W

     

Watts

 

 

          

 

 

 

 

 

spm      

Revolutions or 

   

 

               reciprocation per minute

Double insulated 

Regulator compliance mark

Maximum cutting cap 
for timber

Warning

Read instruction manual

Wear ear protection

Wear eye protection

Wear face mask

n

o      

No load speed

1.   After each use, blow air through the tool housing to ensure it is free from all dust

particles that may build up. Build up of dust particles may cause the tool to
overheat and fail.

2.   If the enclosure of the tool requires cleaning do not use solvents but a moist soft

cloth only. Never let any liquid get inside the tool; never immerse any part of the
tool into a liquid.

3.  When the carbon brushes wear out the tool will spark and/or stop. The brushes are

a wearing component of the tool and should be replaced prior to the carbon
wearing out fully. Brushes will wear out after many uses but before they do take
the tool to an electrician or a power tool repairer for quick and low cost
replacement. Always replace both brushes at the same time.

Note: 

Ozito Industries will not be responsible for any damage or injuries caused by

the repair of the tool by an unauthorised person or by mishandling of the tool.  

 

 

 

 

 

Содержание OZJS400A















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды