WARNING!
When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of fire, electric shock, personal injury and
material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency,
before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The electrical motor has been designed for 230V and 240V only. Always check that the power supply
corresponds to the voltage on the rating plate.
Note:
The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.
This tool is double insulated; therefore no earth wire is required.
Note:
Double insulation does not take the place of normal safety precautions when operating
this tool. The insulation system is for added protection against injury resulting from a possible
electrical insulation failure within the tool.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to
avoid a hazard.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead
not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and
electric shock.
Residual Current Device (RCD)
The pressure washer must be protected by a residual current device (rated at 30mA or less). A residual
current device reduces the chance of electric shock.
WARNING!
The appliance is not to be used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction. Young children should be
supervised to ensure that they do not play with the appliance.
WARNING!
High pressure injection injuries are considered to be medical emergencies. In
the event of a high pressure injection injury occurring, seek medical advice immediately.
WARNING!
It is prohibited to use Pressure Washers on materials containing asbestos
(Cement sheet roofs, Fences, Walls etc.). Large numbers of asbestos fibres may be released
into the air, posing a serious health hazard. If unsure about the materials you are spraying, it is
recommended that you contact your local council or government authority.
• Before connecting a tool to a power source (mains switch power point receptacle, outlet, etc.) be
sure that the voltage supply is the same as that specified on the nameplate of the tool. A power
source with a voltage greater than that specified for the tool can result in serious injury to the user, as
well as damage to the tool. If in doubt, do not plug in the tool. Using a power source with a voltage
less than the nameplate rating is harmful to the motor.
• Unsafe operation of your high pressure cleaner could lead to serious injury or death to you or others.
• The spray gun/wand is a powerful cleaning tool that could look like a toy to a child.
• Improper control of gun/wand can result in injuries to self, others and property damage. Reactive
force from the spray can result in gun/lance movement, potentially causing the operator to slip, fall or
misdirect the spray.
• Become familiar with the operation and controls of the pressure cleaner.
• Keep children away from the pressure cleaner at all times.
• Never modify or remove the safety features of this product.
• Do not operate the machine with missing, broken or unauthorized parts.
• Never leave wand unattended while unit is running.
• Keep work area free of obstacles.
•
Stand on stable surface and grip gun/lance firmly. Expect the gun to kick back when engaged
•
Do not use to pump flammable or explosive liquids such as gasoline, fuel oil, kerosene,solvents
or thinners. Pump should only be used with liquids compatible with pressure washer component
materials. Failure to follow to this warning can result in serious personal injury, death and/or property
damage.
• Only use cleaning agents designed for pressure washers. The use of other cleaning agents or
chemicals may adversely affect the safety and/or operation of the appliance.
• Do not use the appliance within range of persons unless they wear protective clothing.
• High pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons,
animals, live electrical equipment or the appliance itself.
• Do not direct the jet against yourself or others in order to clean clothes or foot-wear.
• To ensure appliance safety, use only original spare parts from the manufacturer or approved by the
manufacturer.
•
High pressure hoses, fittings and couplings are important for the safety of the appliance. Use only
hoses, fittings and couplings recommended by the manufacturer.
• Do not use the appliance if a supply cord or important parts of the appliance are damaged, e.g.
safety devices, high pressure hoses, trigger gun.
•
Water that has flowed through a backflow preventer is considered to be non-potable.
• Depending on the application, shielded nozzled can be used for high pressure cleaning, which will
reduce the emission of hydrous aerosols dramatically. However, not all applications allow the use of
such a device. If shielded nozzles are not applicable for the protection against aerosols, a respiratory
mask of class FFP 2 or equivalent may be needed, depending on the cleaning environment.
•
The electric supply connection shall be made by a qualified electrician and comply with IEC60364-1.
It is recommended that the electric supply to this machine should include either a residual current
device that will interrupt the supply if the leakage current to earth exceeds 30mA for 30ms or a
device that will prove the earth circuit.
• Never touch the mains plug or power outlet with wet hands
• Always disconnect the product from the power outlet when leaving the machine unattended.
•
This product must not be connected to the potable water mains without backflow prevention. Check
local and national plumbing regulations before connecting the machine to the potable water mains.
• Do not operate the machine at temperatures below 0 degrees.
• If an extension cord is used, it shall be suitable for outdoor use, and the connection has to be kept
dry and off the ground. It is recommended that this is accomplished by means of a cord reel which
keeps the socket at least 60 mm above the ground.
• It is recommended that a reinforced garden hose (with minimum diameter of 12mm) is used for the
inlet connection.
• During use of high pressure cleaners, aerosols may be formed. Inhalation of aerosols can be
hazardous to health.
HIGH PRESSURE WASHER SAFETY WARNINGS
GENERAL POWER TOOL SAFETY WARNINGS
ELECTRICAL SAFETY
WARNING!
Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings
refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool.
Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a
cord suitable for outdoor use reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your
finger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of tools allow you to become complacent and
ignore tool safety principles.
A careless action can cause severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application.
The correct power
tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools.
Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools.
Check for misalignment or binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed.
Use of the power tool for
operations different from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualified repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is maintained.
