background image

WARNING!

 

This product is intended for pumping water in a Home Domestic 

application. Do not use it for corrosive, abrasive, explosive or dangerous liquids. 

Fluids other than water will damage the water pump and/or create a fire hazard. Failure to 

follow all instructions listed below may result in electric shock, fire and/or serious injury.

This appliance is not intended for use by person (including children) with reduced 

physical, sensory or mental capabilities, or lack of experience and knowledge, unless 

they have been given supervision or instruction concerning use of the appliance by a 

person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

•   Ensure the water pump is disconnected from mains power when installing.
•    Do not install or operate the water pump in an explosive environment or near flammable 

material.

•   Do not operate the water pump without liquid.
•   Do not run the water pump dry.

WARNING!

 

The water pump together with associated pipework operate under 

pressure. Do not disconnect water pump or pipework until internal pressure has 

been released. Failure to do this could result in personal injury and damage to 

property.

•    Avoid inserting hands into the inlets/outlets of the water pump while it is connected to 

power.

•    Before using the water pump, always inspect it visually. Do not use the pump if it is 

cracked and/or damaged. If the water pump is damaged, contact Ozito customer service.

•    The water pump has a built-in thermal protection overload switch. The water pump stops 

if an overload occurs. The motor restarts automatically after it has cooled down.

•   The pump must not be used when people are in the water.
•    Never work or perform maintenance on the pump without first making sure it has been 

disconnected from the mains power.

•   Pollution of the liquid could occur due to leakage of lubricants 

IMPORTANT:

•   Avoid inserting hands into the mouth of the pump if it is connected to the mains.
•    The electrical connection must always be made in a dry area. Make sure that electrical 

connections are protected from inundations.

•   Protect the plug and the power cable from heat, oil or sharp edges.
•   If damaged, The power cable must be replaced by a qualified electrician.
•    When operating in swimming pools, garden ponds and similar places, the device must be 

provided with a residual current of not more than 30 mA by means of a residual-current-

operated protective device.

•    If pump is intended for transferring water for drinking use food grade fitting and hoses/

pipes. Ensure they are clean before use. 

PRESSURE PUMP SAFETY WARNINGS

WARNING!

 

When using mains-powered tools, basic safety precautions, 

including the following, should always be followed to reduce risk of fire, 

electric shock, 

personal injury and material damage.

Read and understand the manual prior to operating this pump.

Save these instructions and other documents supplied with this pump for future reference. 

The electric motor has been designed for 230V and 240V only. Always check that the power 

supply corresponds to the voltage on the rating plate.

Note:

 The supply of 230V and 240V on Ozito pumps are interchangeable for Australia and 

New Zealand. This pump is earthed in accordance with AS/NZS 60335-2-41.

Note: 

The power outlet used for the water pump must be protected by a 30mA residual 

current device or earth leakage circuit breaker. If the power outlet is external, ensure that 

it is weather proof. If the supply cord is damaged, it must be replaced by an electrician or 

a power tool repairer to avoid a hazard. The water pump has a built-in thermal protection 

overload switch. The water pump stops if an overload occurs. The motor restarts 

automatically after it has cooled down.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this product. 

Before use, inspect the extension lead for signs of damage, wear and ageing. Replace the 

extension lead if damaged or defective. Then using an extension lead on a reel, always 

unwind the lead completely. Use of an extension lead not suitable for the power input of this 

product or which is damaged or defective may result in a risk of fire and electric shock.

WARNING!

 Read all safety warnings and all instructions. 

Failure to follow the 

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in 

the warnings refers to your mains-operated (corded) power tool or battery-operated 

(cordless) power tool.
1.   Work area safety 

a.  

 Keep work area clean and well lit

. Cluttered or dark areas invite accidents. 

b.  

 Do not operate power tools in explosive atmospheres, such as in the presence of 

flammable liquids, gases or dust.

 Power tools create sparks which may ignite the dust 

or fumes. 

c.  

 Keep children and bystanders away while operating a power tool.

 Distractions can 

cause you to lose control.

2.   Electrical safety 

a.  

 Power tool plugs must match the outlet. Never modify the plug in any way.  

Do not use any adapter plugs with earthed (grounded) power tools.

 Unmodified 

plugs and matching outlets will reduce risk of electric shock. 

b.    

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, 

ranges and refrigerators. 

There is an increased risk of electric shock if your body is 

earthed or grounded. 

c.    

Do not expose power tools to rain or wet conditions.

 Water entering a power tool will 

increase the risk of electric shock. 

d.  

 Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the 

power tool. Keep cord away from heat, oil, sharp edges or moving parts.

 Damaged 

or entangled cords increase the risk of electric shock. 

e.    

When operating a power tool outdoors, use an extension cord suitable for outdoor 

use.

 Use of a cord suitable for outdoor use reduces the risk of electric shock. 

f.  

 If operating a power tool in a damp location is unavoidable, use a residual current 

device (RCD) protected supply.

 Use of an RCD reduces the risk of electric shock. 

3.   Personal safety 

a.  

 Stay alert, watch what you are doing and use common sense when operating a 

power tool. Do not use a power tool while you are tired or under the influence of 

drugs, alcohol or medication.

 A moment of inattention while operating power tools may 

result in serious personal injury. 

b.  

Use personal protective equipment. Always wear eye protection.

 Protective 

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection 

used for appropriate conditions will reduce personal injuries. 

c.  

 Prevent unintentional starting. Ensure the switch is in the off-position before 

connecting to power source and/or battery pack, picking up or carrying the tool. 

Carrying power tools with your finger on the switch or energising power tools that have 

the switch on invites accidents. 

d.    

Remove any adjusting key or wrench before turning the power tool on.

  

A wrench or a key left attached to a rotating part of the power tool may result  

in personal injury. 

e.    

Do not overreach. Keep proper footing and balance at all times.

 This enables better 

control of the power tool in unexpected situations. 

f.  

 Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing 

and gloves away from moving parts.

 Loose clothes, jewellery or long hair can be 

caught in moving parts.

g.    

If devices are provided for the connection of dust extraction and collection 

facilities, ensure these are connected and properly used.

 Use of dust collection can 

reduce dust-related hazards.

4.   Power tool use and care 

a.  

 Do not force the power tool. Use the correct power tool for your application. 

The 

correct power tool will do the job better and safer at the rate for which it was designed. 

b.    

Do not use the power tool if the switch does not turn it on and off.

 Any power tool 

that cannot be controlled with the switch is dangerous and must be repaired. 

c.  

 Disconnect the plug from the power source and/or the battery pack from the 

power tool before making any adjustments, changing accessories, or storing 

power tools.

 Such preventive safety measures reduce the risk of starting the power tool 

accidentally. 

d.    

Store idle power tools out of the reach of children and do not allow persons 

unfamiliar with the power tool or these instructions to operate the power tool.

 

Power tools are dangerous in the hands of untrained users. 

e.    

Maintain power tools. Check for misalignment or binding of moving parts, 

breakage of parts and any other condition that may affect the power tool’s 

operation. If damaged, have the power tool repaired before use.

 Many accidents are 

caused by poorly maintained power tools. 

f.  

 Keep cutting tools sharp and clean.

 Properly maintained cutting tools with sharp 

cutting edges are less likely to bind and are easier to control. 

g.    

Use the power tool, accessories and tool bits etc. in accordance with these 

instructions, taking into account the working conditions and the work to be 

performed. 

Use of the power tool for operations different from those intended could 

result in a hazardous situation. 

5.   Service 

a.  

 Have your power tool serviced by a qualified repair person using only identical 

replacement parts. 

This will ensure that the safety of the power tool  

is maintained.  

b.  

 If the supply cord is damaged, it must be replaced by the manufacturer,

  

its service agent or similarly qualified persons in order to avoid a hazard.  

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

Содержание CPPW-805









Отзывы: