background image

1

6. SPRAYING PROCEDURE

3   Begin 15cm off the edge of the area being sprayed. Start the 

movement of the stroke before squeezing the trigger.

4   Release the trigger once 

past the opposite edge of 

the area being sprayed.

15cm

2   Turn the Airless Sprayer on. 

Release the trigger lock. 

Ensure the priming lever is 

in the spray position.

30cm

Note:

 Ensure the Airless Sprayer has been properly primed before 

commencing spraying procedure.

1   Stand 30cm from area to 

be sprayed. Maintain this 

distance.

I

O

1   Move the gun with the entire arm, not by flexing the wrist. This 

will keep the spray gun at right angles to the surface, keeping 

the pattern even.

2   Keep the spray gun perpendicular to the surface, so spray 

distance is consistent.

Helpful Hints

1   Do not spray outdoors on a windy day as the results may be 

unsatisfactory.

2   Only apply one coat at a time, always allow a coat to completely 

dry before adding another coat.

3   Avoid stopping and starting as this can lead to a patchy finish, 

It is best to start spraying outside the surface to be sprayed and 

avoid stopping in the middle of the surface, continue just past the 

opposite edge.

3   Overlap each stroke by 30% to ensure even coverage.

30%

7. SPRAYING TECHNIQUE 

ASG-6000

Содержание ASG-6000














Отзывы: