ASSEMBLY INSTRUCTIONS
MODEL
W770, 23’6” x 18’6”
16 Person Cabin Tent
IMPORTANT:
WE ADVISE YOU TO ASSEMBLE THE TENT ONCE BEFORE
GOING CAMPING TO BECOME FAMILIAR WITH THE ASSEMBLY OF THE TENT.
NOTE:
PLEASE LOOK AT THE REPLACEMENT PARTS DIAGRAM TO SEE HOW
YOUR FRAME IS ASSEMBLED.
TO PROLONG THE LIFE OF THE TENT FLOOR, SELECT A LEVEL, CLEAN AREA
FOR THE CAMPSITE. TO PREVENT DAMAGE TO THE ZIPPER, UNZIP THE
DOORS TO ALLOW AIR TO ENTER THE TENT.
TO IMPROVE THE WEATHER RESISTANCE OF YOUR TENT, IT IS ADVISABLE
TO USE SEAM SEALER TO COAT ALL EXPOSED SEAMS. YOU SHOULD APPLY
ONLY TO THE INSIDE SEAMS OF THE TENT AND UNDERSIDE OF THE TENT FLY.
IF APPLIED TO THE OUTSIDE OF SEAMS, DISCOLORATION OF YOUR TENT
MAY OCCUR. SEAM SEALER IS AVAILABLE IN THE CAMPING SECTION OF
ANY LOCAL SPORTING GOODS STORE.
STEP 1:
Spread tent out flat, floor side down. Unzip doors to allow air to enter the tent.
STEP 4:
While leaving the tent flat on the ground, insert the three main roof
poles (A) through the blue sleeves on the roof of the tent.
STEP 7
: Insert one end of the eave pole into eave joints. Gently flex and insert
opposite end into the corresponding joint. Repeat for all six poles.
NOTE:
Please be sure that the metal ferrules on the end of the fiberglass poles
are completely inserted into the hubs or the poles may be damaged during set up.
The assembled tent should
appear as shown.
STEP 3:
Extend each of the 12 fiberglass
poles by pulling out each section and
placing ends into the connecting ferrules.
The three poles of the same length (A) are
the main roof poles. The two longest poles
(D) with white tape are the side room poles.
The six poles of the same length (B) are the
roof eave poles. The shortest pole is the front
entry roof pole (E).
Top View
NOTE:
To take down tent, follow steps above in the reverse order. Be sure to
leave doors unzipped.
MAKE SURE TENT IS CLEAN AND DRY BEFORE
STORING
. Place stakes into stake bag and poles into pole bag, which are
provided. The tent should be folded into equal parts toward the center to
distribute the bulk. Fold fly and lay on top. Start a small tight roll, the width of
your carry bag, with the pole bag placed at the end opposite the doors. Roll
tent toward doors to allow air to escape. Once rolled, secure with strings or
rope, and place into carry bag.
STEP 2:
Stake tent to the ground by inserting metal stakes through
the stake loops located at the six corners. Hammer stakes into
ground at a 45° angle and pull tent floor out even and snug.
Continue to stake down all intermediate stake loops and rings.
STEP 5:
Locate the six plastic eave joints (G) that are
attached to the tent canopy. Flex the fiberglass roof poles
and insert the ends of the poles into the center opening of
the eave joints on the side with three openings. The fourth
opening should face down as pictured.
Tent should appear
as shown.
STEP 8:
Extend each of the six steel poles (C) by pulling out each wire-corded
section and placing the jointed ends into the connected pole sections.
STEP 9:
Insert the end of one of the steel poles (D-ring near top)
into the bottom opening of one of the eave hubs. Lift up on the
pole and while raising the tent place the bottom end of the steel
pole over the pin at the base of the tent.
STEP 10:
Using the five remaining steel poles, repeat STEP 8 & 9 working your
way around the tent.
STEP 11:
Slide the two side room poles (D) through the blue pole
sleeves above each of the side room doors. With an adult on each
end of one of the poles, flex into an arch and place the ends over
the pins at base of tent. Clip plastic hooks to frame. Repeat with the
other side room tent pole.
STEP 12:
Insert the fiberglass front entry roof pole (E) through the grey sleeve
at the front of the tent.
STEP 13:
Extend each of the two steel porch upright poles with pre-bent sections. (F)
STEP 14:
Place the pre-bent end of steel entry upright pole (F)
onto one end of the front entry roof pole (E). Place straight end
onto the pin at the base of the tent. Repeat with the second porch
upright pole (F) on the other side of the tent. Clip plastic hooks
around the steel upright poles.
STEP 16:
Secure the fly to tent by wrapping hook and loop
fasteners at edge of fly around poles.
STEP 17:
Guy ropes have been provided for the fly. Extend
guy ropes and make a loop at the end of guy ropes by using
slider (as shown) and place loop over tent stakes. Hammer
stake into ground at a 45° angle. Adjust slider to make guy
rope tight. Repeat with the remaining guy ropes.
STEP 15:
Unfold fly and place over tent. Make certain that the
dark grey panel is positioned over front porch entry. Attach fly
to tent by using the plastic “S” hooks on the fly to the D-rings on
the upright poles and fabric loops on the tent for the side rooms.
STEP 6:
Insert the 6 eave poles (B) through the grey pole sleeves on the eaves of the tent.
D
D
B
G
G
G
G
G
G
B
B
B
B A A
A
A
A
A
B
E
C
C
C
F
F
C
C
C
C
G
B
B
A