Oxbox J951X D Series Скачать руководство пользователя страница 26

Страница: 26 / 44

Figure 28. Regulator Capscrew

Capscrew

6. The manifold pressure must be set to the appropriate

value for each installation by a qualified installer, service

agency or the gas supplier.

WARNING:

Do not attempt to drill the gas orifices. Use only

factory supplied orifices. Improperly drilled

orifices may cause fire, explosion, carbon

monoxide poisoning, personal injury or death.

a.) Obtain the manifold pressure setting required for

this installation by referring to

Table 8 (page 33)

for

Propane or

b.) Remove the regulator capscrew (

Figure 28

) from the

INLET side of the regulator.

c.) Slowly turn the adjustment screw inside the regulator

to obtain the appropriate manifold pressure.

NOTE:

Turning the screw clockwise increases the

pressure and turning the screw counter-clockwise

decreases the pressure. To prevent backing the screw

all the way out from the valve, turn the screw slowly.

d.) Replace and tighten the regulator capscrew over the

adjustment screw.

Verifying & Adjusting Temperature Rise

After installation of the furnace, confirm the temperature rise

of the furnace is within the limits specified on the rating plate.

Any temperature rise outside the specified limits could result

in premature failure of the heat exchanger.
1. Place thermometers in the return and supply air stream

as close to the furnace as possible. The thermometer on

the supply air side must be shielded from direct radiation

from the heat exchanger to avoid false readings.

2. Adjust all registers and duct dampers to the desired position

and run the furnace for 10 to 15 minutes before taking

any temperature readings. The temperature rise is the

difference between the supply and return air temperatures.

For typical duct systems, the temperature rise will fall within the

limits specified on the rating plate with the blower speed at the

factory recommended setting. If the measured temperature

rise is outside the specified limits, it may be necessary to

change the speed of the blower.

NOTE:

Lowering the blower speed will increase the

temperature rise and a higher blower speed will decrease

the temperature rise.

The furnace is equipped with a 5-speed ECM motor. Heating

and cooling speed selection is made by moving the switch on the

integrated control inside of the furnace. The furnace is shipped

from the factory pre-wired for 4 blower speeds. There is a fifth

alternate speed available on the motor. To utilize the alternate

speed, remove the wire at the motor plug of the desired speed to

be changed (H, MH, ML, L). Reconnect this wire to the alternate

motor plug speed tap.

Verifying Burner Operation

CAUTION:

The door over the burners may only be open

for inspection purposes only. The door must be

installed during unattended operation.

1. Remove the burner compartment door.

2. Set the thermostat above room temperature and observe

the ignition sequence.

NOTE

: The burner flame should

carry over immediately between all burners without lifting

off, curling, or floating. The flames should be blue, without

yellow tips.

3. After validating the flame, change thermostat setting to

below room temperature.

4. Verify the burner flame is completely extinguished.

5. Replace the burner compartment door.

Verifying Operation of the Supply Air Limit

Switch

NOTE

: A properly functioning limit switch should turn off

the gas valve when the return is blocked (time depends on

how well the return air is blocked). The circulating air and

combustion blowers should continue to run when the limit

switch opens.
1. Verify the blower door is securely mounted in place and

that there is power to the furnace.

2. Block the return airflow to the furnace by installing a close-

off plate in place of or upstream of the filter(s).

3. Set the thermostat above room temperature and observe

the Operating Sequence.

4. Remove the close-off immediately after the limit switch

opens. If the furnace continues to operate with no return

air, set the thermostat below room temperature, shut off

power to the furnace, and replace the limit switch.

System Operation

(Gas) Heating Mode

When the thermostat calls for heating, the circuit between

and

is completed. The furnace control board initiates the

ignition sequence. Approximately 30 seconds after the gas

flame has proven, the blower motor will start. The blower will

continue to operate after the call for heat has been removed

for a selectable (switch on furnace control board) number of

seconds.

NOTE:

All on- and off-delays for heating continue

to be controlled by the furnace control board.

Cooling Mode

When the thermostat calls for cooling or heat pump heating,

the circuit between

, and

(

is ignored by the blower)

is completed. The blower runs at the selected cooling motor

torque.

Manual Fan

Select the speed using the jumper on the control board.

Содержание J951X D Series













































Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды

Oxbox J951X D Series, Руководство по установке

Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды