Owon SDS5032E Скачать руководство пользователя страница 31

Страница: 31 / 90

5. Advanced User Guidebook

Press

button to choose the Format, including dB, Vrms.

Press

button, the zoom window will display at the left of the screen, turn the

knob to zoom in or out the wave of the multiple including ×1, ×2, ×5, ×10.

To select the FFT window

■

There are four FFT windows. Each one has trade-offs between frequency resolution and

magnitude accuracy. What you want to measure and your source signal characteristics
help you to determine which window to use. Use the following guidelines to select the
best window.

Type Characteristics

Window

Rectangle

Best solution for frequency, worst for magnitude.

Best type for measuring the frequency spectrum of
nonrepetitive signals and measuring frequency
components near DC.

Recommend to use for:

Transients or bursts, the signal level before and
after the event are nearly equal.

Equal-amplitude sine waves with frequencies
those are very close.

Broadband random noise with a relatively slow
varying spectrum.

Hamming

Better solution for magnitude than Rectangle, and
good for frequency as well. It has slightly better
frequency resolution than Hanning.

Recommend to use for:

Sine, periodic and narrow band random noise.

Transients or bursts where the signal levels
before and after the event are significantly
different.

Hanning

Good for magnitude, but poorer frequency
resolution than Hamming.

Recommend to use for:

Sine, periodic and narrow band random noise.

Transients or bursts where the signal levels
before and after the event are significantly
different.

Содержание SDS5032E



























































































Результаты поиска

Содержание SDS5032E

Отзывы:

Похожие инструкции для SDS5032E

Бренды по названию

Популярные бренды

Owon SDS5032E, Руководство пользователя

Результаты поиска

Содержание SDS5032E

Отзывы:

Похожие инструкции для SDS5032E

Бренды по названию

Популярные бренды