Owon SDS1000 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 68

background image

4.Advanced User Guidebook

27

How to Operate the Function Menu

The function menu control zone includes 4 function menu buttons:

Utility,

Measure, Acquire, Cursor,

and 2 immediate-execution buttons:

Autoset,

Run/Stop.

How to Set the Sampling/Display

Push the

Acquire

button, the Sampling and Display menu is shown in the right as

follows:

Persist

When the

Persist

function is used, the persistence display effect of the picture

tube oscilloscope can be simulated. The reserved original data is displayed in fade
color and the new data is in bright color.

(1) Push the

Acquire

button.

Function

Menu

Setting

Description

Acqu Mode

Sample

Peak Detect

Average

Normal sampling mode.

Use to capture maximal and minimal samples.
Finding  highest  and  lowest  points  over
adjacent intervals. It is used for the detection of
the jamming burr and the possibility of reducing
the confusion.

It is used to reduce the random and don't-care
noises,  with  the  optional  number  of  averages.
Turn the

M

knob to select 4, 16, 64, 128 in the

left menu.

Type

Dots

Vect

Only the sampling points are displayed.
The  space  between  the  adjacent  sampling
points  in  the  display  is  filled  with  the  vector
form.

Persist

OFF

1 Second

2 Seconds
5 Seconds

Infinity

Set the persistence time

XY Mode

ON

OFF

Turn on/off XY display function

Counter

ON

OFF

Turn on/off counter

«
...
30
31
32
33
34
...
»

Содержание SDS1000





































































Отзывы:

Нет отзывов

Похожие инструкции для SDS1000

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: Camozzi Страницы: 2

Бренд: Oktober Страницы: 22

Бренд: Raytech Страницы: 21

Бренд: Teac Страницы: 2

Бренд: laerdal Страницы: 2

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: AAON Страницы: 36

Бренд: CAMAG Страницы: 40

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 15

Бренд: Fayat Group Страницы: 50

Бренд: Halyard Страницы: 88

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды