Owon SDS1000 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 68

background image

3.Quick Start

10

2. Set the Switch in the Oscilloscope Probe as 10X and Connect the

Oscilloscope with CH1 Channel.

Align the slot in the probe with the plug in the CH1 connector BNC, and then
tighten the probe with rotating it to the right side.

Connect the probe tip and the ground clamp to the connector of the probe
compensator.

3. Push the Autoset Button on the front panel.

The square wave of 1 KHz frequency and 5V peak-peak value will be
displayed in several seconds (see

Figure 3-5 Auto set

Check CH2

、

CH3 and CH4 by repeating Step 2 and Step 3.

How to Implement the Probe Compensation

When  connect  the  probe  with  any  input  channel  for  the  first  time,  make  this
adjustment to match the probe with the input channel. The probe which is not
compensated  or  presents  a  compensation  deviation  will  result  in  the
measuring  error  or  mistake.  For  adjusting  the  probe  compensation,  please
carry out the following steps:

1. Set the attenuation coefficient of the probe in the menu as 10X and that of

the switch in the probe as 10X

(see "

How to Set the Probe Attenuation

" on P11), and connect the probe with the CH1 channel. If a

probe hook tip is used, ensure that it keeps in close touch with the probe.
Connect the probe tip with the signal connector of the probe compensator
and connect the reference wire clamp with the ground wire connector of
the probe connector, and then push the

Autoset

button on the front panel.

2. Check the displayed waveforms and regulate the probe till a correct

«
...
13
14
15
16
17
...
»

Содержание SDS1000





































































Отзывы:

Нет отзывов

Похожие инструкции для SDS1000

Бренд: AccuMed Страницы: 14

Бренд: TAS Страницы: 25

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: Datalogic Страницы: 48

Бренд: PageFlip Страницы: 32

Бренд: Fellowes Страницы: 20

Бренд: Ransomes Страницы: 282

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Jacto Страницы: 64

Бренд: Yanmar Страницы: 49

Бренд: Fagor Страницы: 12

Бренд: Baltic Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды