background image

CHANGES:

The material in this document is for information purposes only and subject to change without notice. While 

reasonable efforts have been made in the preparation of this document to assure its accuracy, OWC, its 

parent, partners, affiliates, officers, employees, and agents assume no liability resulting from errors or 

omissions in this document, or from the use of the information contained herein. OWC reserves the right 

to make changes or revisions in the product design or the product manual without reservation and without 

obligation to notify any person of such revisions and changes.

FCC STATEMENT:

Warning! Modifications not authorized by the manufacturer may void the user’s authority to operate this 

device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This equipment generates, uses and can radiate 

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference with radio or television reception, 

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:

 -Reorient or relocate the receiving antenna.
 -Increase the separation between the equipment and receiver.
 -Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

WARRANTY:

The Accelsior 1M2 has a 

5 Year OWC Limited Warranty

 if it was bundled with a drive. If the Accelsior 1M2 did 

not ship with a drive, it has a 

1 Year OWC Limited Warranty.

 For up-to-date product and warranty information, 

please visit the 

product web page

.

COPYRIGHTS AND TRADEMARKS:

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by 

any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent 

of OWC.

© 2020 Other World Computing, Inc. All rights reserved. Accelsior, OWC, and the OWC logo are trademarks 

of New Concepts Development Corporation, registered in the U.S. and/or other countries. Mac and macOS 

are trademarks of Apple Inc., registered in the U.S. and other countries. Other marks may be the trademark or 

registered trademark property of their owners.

OWCMANACC1M2 – 10.30.2020

Содержание ACCELSIOR 1M2











Отзывы: