background image

 

17

 

 

Installation site preparation 

 

Cabling requirements 

 

Connecting to power 

 

 
 

Installation on Wall 

 

Live-FSH16T Fast Ethernet Switch can be mounted on a wall with wall anchors and 
screws. 
 
To mount the Switch on wall, please follow the steps below: 
 

 

Drill two holes, the distance between both of which should be 9 cm (such as the 
illustration below). 

 

Insert wall anchors into these two holes. 

 

Drive the screws into the top of the wall anchors. 

 

Mount 

Live-FSH16T 

on the screws. 

 

 

 

Fig. 3-3 Bottom View of the Switch (showing mounting holes) 

 

 

Cabling Requirements 

 
Live-FSH16T Fast Ethernet Switch is primarily targeted as a switching device to 
concentrate your network traffic in a workgroup environment. It fits well into the 
10BASE-T and 100BASE-TX cabling architecture to facilitate UTP end-station 
connections to 10BASE-T/100BASE-TX network. The Uplink port also provides a 
switch-to-switch cabling extension up to 100 meters. 
 
The 16 RJ-45 station ports (MDI-X), which require either UTP or STP cable connection, is 
compliant with 10/100 BASE Fast Ethernet standard. Thus, when configuring within the 
10BASE-T/100BASETX cabling architecture, the UTP cabling distance should be within 
a maximum distance of 100m. 
 

9 cm 

Содержание Live-FSH16T

































Отзывы: