background image

en

28

Installation

Commissioning

Adjustments

Tr

oubleshooting

Data comm

unication

3.4 

 Additional  functions

In this menu, additional functions can be selected and 
adjusted, as long as there are free relays available. The 
following additional functions are available:
•  Function block 1
•  Function block 2 
•  Stratifi ed return
•  Error relay

 Function block

In addition to the pre-defi ned optional functions, up 
to 2 function blocks consisting of thermostat func-
tions, timer and differential functions are available. 
With the help of these function blocks, further com-
ponents and functions respectively can be controlled.
To each function block, sensors and free relays can 
be allocated. Sensors already in use can be allocated 
again without impeding their control functions.

Within a function block the functions are intercon-
nected (AND gate). This means that the conditions 
of all the activated functions have to be fulfi lled (e. g. 
thermostat and timer) for switching the allocated re-
lay. As soon as one condition is not fulfi lled, the relay 
switches off.

 Thermostat function

The relay allocated to the function block switches on, 
when the adjusted switch-on temperature (Th(x)on) 
is reached. It switches off when the adjusted switch-
off temperature (Th(x)off) is reached. The switching 
conditions of all other activated functions of the 
function block have to be fulfi lled as well.
Adjust the heating function with Th(x)off > Th(x)on, 
the  cooling  function  with Th(x)on  > Th(x)off. The 
temperatures cannot be set to an identical value. 

 

T function

The relay allocated to the function block is switched 
on as soon as the adjusted switch-on temperature 
difference (

Th(x)on) is reached. It is switched off as 

soon as the adjusted switch-off temperature differ-
ence (

Th(x)off) is reached.

If the switch-on difference is reached, the pump is 
activated at full speed for 10 s. Then, the speed is re-
duced to the adjusted minimum pump speed value. 
If the temperature difference reaches the adjusted 
nominal temperature difference, the pump speed 
increases by one step (10 %). If the temperature dif-
ference increases by the adjustable 

Rise

 value, the 

pump speed increases by 10 % respectively until the 
maximum pump speed of 100 % is reached.

 

Timer

The relay allocated to the function block switches 
on when the current operating time is within the ad-
justed time frame.

 

Flow rate dependent de-/activation

The relay allocated to the function block switches 
on when the adjusted switch-on fl ow rate 

dVon

 is 

reached at the fl ow rate sensor. It switches off when 
the adjusted switch-off fl ow rate 

dVoff

 is reached.

If the 

Inverted

 option is activated, the relay oper-

ates vice versa.
The 

Sensor dV

 channel indicates the fl ow rate sen-

sor currently used.

 

Reference relay

Up to 3 reference relays can be selected. Whether 
the reference relays are to be switched in series 
(AND), in parallel (OR), in series inverted (NAND) 
or in parallel inverted (NOR) can be adjusted in the 
Mode channel.
In the OR mode, the switch-on condition for the ref-
erence relay function is considered fulfi lled when at 
least one of the reference relays is active.
If none of the reference relays is active, the switch-on 
condition for the reference relay function is consid-
ered unfulfi lled.
In the NOR mode, the switch-on condition for the 
reference relay function is considered fulfi lled when 
none of the reference relays is active.

Содержание Regtronic RQ









































Отзывы: