background image

6

V1.47

Securing with a safety cable

Secure the fixture with a safety cable (or other secondary attachment) that is approved for the weight of 
the fixture so that the safety cable will hold the fixture if a primary attachment fails.

Loop the safety cable through the eyebolt in the back of the fixture and around a secure anchoring point. 
Do not loop the safety cable around the fixture’s mounting bracket only, as this will leave the fixture un

-

secured if it separates from the bracket.

DMX-512 connection/connection between fixtures

Occupation of the XLR-connection:

1. Group

2. Signal (-)

3. Signal (+)

DMX OUT

1. Group

2. Signal (-)

3. Signal (+)

DMX IN

If you are using controllers with this occupation, you can connect the DMX-output of the controller directly 
with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other 
XLR-outputs, you need to use adapter-cables.

Building a serial DMX-chain:

Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture.
Always connect one output with the input of the next fixture until all fixtures are connected.

DMX-512 connection with DMX terminator:

For installations where the DMX cable has to run a long distance or is in an electrically noisy environ

-

ment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing 
corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with 
a 120 resistor connected between pins 2 and 3, which is then plugged into the output XLR socket of the 
last fixture in the chain.

Caution: 

At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ω re

-

Содержание Honor 250T Zoom

















Отзывы: