RR2160
MkII Owner’s Manual
Outlaw Audio
RR2160
MkII Stereo RetroReceiver
9
R16 Analog 1 Inputs
(Pages 12, 22)
R17 Analog 2 Inputs
(Pages 12, 22)
R18 Analog 3 Inputs
(Pages 12, 22)
R19 Analog 4 Inputs
(Pages 12, 22)
Connect the line-level analog audio outputs of
sources such as a CD player, DVD/Blu-ray
Disc player, network media player, Bluetooth
or streaming adapter or dongle, satellite or
cable box to these jacks.
R20 Record Output jacks
(Pages 12, 24)
Connect analog audio inputs from your
recording device or encoder for digital storage
to these jacks.
Note: These are fixed-level outputs and are not
affected by the RR2160
MkII’s volume control. If
you’re using a portable recording device
(MiniDisc recorder, etc.), you may use shielded
stereo “Y” cords (3.5 mm stereo miniplug to
two RCA-type jacks) to go from it to the
RR2160
MkII.
R21 External Processor Loop connections
(Page 12)
Connect an external processor (equalizer,
electronic crossover, surround processor, etc.)
to these jacks. These outputs are also fixed-
level. The Loop input may also be used as an
additional analog input.
R22 Bass Management selector switch
(Page 16)
This switch lets you adjust the internal
crossover (bass management system) to route
user-selected low frequencies to the
subwoofer output (R25) while the rest of the
audio signal is sent to the amplifier and then to
the main loudspeakers.
R23 Preamplifier outputs
(Page 17)
These outputs allow you to connect a high
output power amplifier if needed. Simply
remove the jumpers and connect the preamp
outputs to the inputs of the additional amplifier.
Note: Removing the jumpers means that the
RR2160
MkII’s internal amplifier does not receive a
signal and cannot send any output to the
speakers connected to it. Use shielded “Y”
cords to connect both the internal amplifier and
another amplifier to the receiver’s preamp
section.
R24 Main Amp inputs
(Page 17)
These inputs are normally connected to the
preamplifier outputs by jumpers. (See R23
above.)
R25 Subwoofer outputs
(Page 17)
Connect a powered subwoofer to either the
SUB1 or SUB2 output. Make sure you’ve set
the Bass Management selector switch (R22)
correctly. The output from this connector is
variable and controlled by the Master Volume
setting (F21).
R26 Left Speaker Binding Posts
(Page 15)
Use these binding posts to connect your
primary (Speakers A) and secondary
(Speakers B) speakers to the RR2160
MkII.
R27 AC Socket
(Page 18)
Connect the supplied AC power cord to this
socket before turning on the Master Power
Switch (R11).
+
-
+
-
+
-
+
-
ETHERNET
MAIN
IN
SUB1
MASTER POWER
ON
OFF
OUT
PHONO
PHONO
GROUND
MC MM
IN
1
2
3
4
SUB2
PRE
OUT
REC
OUT
AUDIO IN
EXTERNAL
PROCESSOR
L
R
L
R
L
R
BASS
MANAGEMENT
ACCESSORY POWER
5V DC / 1.0A MAX
COAX 1
PC-USB
COAX 2
OPT 1
OPT 2
TRIGGER
OUT
IR-IN
1
2
IR-OUT
USB PLAY/
UPGRADER
SERIAL NUMBER:
60
80 100 BP
RIGHT
SPEAKERS
A
B
A
B
LEFT
SPEAKERS
HD RADIO ANT.
RR2160
MkII
Outlaw Audio, LLC
Easton, MA USA
www.outlawaudio.com
Designed in the USA
Made in China
AC INPUT 120V~ 60Hz
POWER CONSUMPTION 400W
WiFi ANT.
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R16 - R19
R20
R21
R22
R23
R25
R26
R27
R15
R24