Learn more at SkeeterDefeater.com
Learn more at SkeeterDefeater.com
©2009 Outdoor Solutions, Inc.
©2009 Outdoor Solutions, Inc.
Initial Set Up
(cont.)
CRU
Installation
The SKEETER DEFEATER
®
Dispenser must be used exclusively with the
SKEETER DEFEATER Contact Insecticide Cylinder Refi ll Unit (CRU).
The SKEETER DEFEATER Contact Insecticide contains pyrethrin,
a botanical insecticide that kills mosquitoes on contact. For more
information on pyrethrin, visit SkeeterDefeater.com. Learn more
about the CRU on page 9 of this manual.
ATTENTION
The SKEETER DEFEATER Dispenser is designed to be used only with the
SKEETER DEFEATER Contact Insecticide. Attempting to install any other
pesticide aerosol may cause the SKEETER DEFEATER Dispenser to
malfunction.
1. With the Spray Head still detached from the Base,
remove the cap
and spray nozzle
from the CRU and place the CRU upright on a fl at
surface outdoors.
2. Be sure the 3-Way Power Switch on the Spray Head is set to “Off.”
3. With the Nozzle pointing away from you, place the Spray Head on top of
the CRU and press down fi rmly on the top of the unit with the palm
of one hand (pictured) until the CRU snaps into place.
4. Move the 3-way Power Switch to the desired operation setting
(see page 6 for more details).
5. Line up the arrow on the top lip of the Base with the OPEN arrow on the
bottom lip of the Spray Head and then twist the Spray Head clockwise to
align arrows in the CLOSE position.
6. Dispose of empty CRUs according to instructions on the label.
5
1.
3.
5.
12
Appendix A – SKEETER DEFEATER
®
Dispenser
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Warning: Changes or modifi cations to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful intereference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the intereference by one or more of
the following measures
• Reorient or relocate the receiving antenna,
• Increase the separation between the equipment and receiver,
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected, or
• Consult the dealer or an experienced radio/TV technician for help.
Appendix B – SKEETER DEFEATER Remote Control
Warning: Changes or modifi cations to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures
• Reorient or relocate the receiving antenna,
• Increase the separation between the equipment and receiver,
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected, or
• Consult the dealer or an experienced radio/TV technician for help.
Remove Cap and
Spray Nozzle BEFORE
Installing CRU.
