After accessing the router admin panel, navigate to
System > System
from the top menu.
Under the tab of
General Settings
, click the
Sync with browser
button to sync the time.
Go to
System > Administration
, input new custom
router password
twice, and save settings.
*Keep the new password in a safe place.
Go to
Network > Wireless
, click the
Edit
button on
SSID: Outdoor-WiFi-xxx
(Mode: Master)
.
Scroll down to
Interface Configuration
, change Wi-Fi SSID on
ESSID
field.
Click the tab of
Wireless Security
, choose
WPA-PSK/WPA2-PSK
on
Encryption
.
Input the Wi-Fi password on the
Key
field, then save settings.
It will use 1-2 minutes to reboot the Wi-Fi hotspot.
On the front page, check the modem status and the signal strength on the
right-side
DEVICE
section.
Go to Network > Interfaces, check the IP and traffic flow of the
MOBILE
interface.
It is non-necessary to change APN unless the mobile carrier requires to do so.
Click the
Edit
button on the
MOBILE
. Tap the
Primary SIM1
(or SIM2)
tab to change APN.
* Check the APN tutorial on https://ezen.link/APN.
It is also not necessary to change the protocol unless default one is no supported.
* Check the protocol tutorial on https://ezen.link/protocol.
Turn on DHCP mode on the phone or computer to obtain a local IP address from the
4G router. To use a static IP address, please comply with the below format.
Computer IP
Subnet mask
Gateway (Router IP)
192.168.30.100~249
( pick one IP from 100~249 )
255.255.255.0
( 24 on Windows )
192.168.30.1
Status
Disabled
Connection attempt failed
Network device is not present
Connected but no internet
Solution
Check if the SIM card is locked.
Re-insert the SIM card and check the signal strength.
The Guardian module is resetting. Wait for 2-3 minutes.
Check if the data plan supports use on a 4G router.
1. Status
2. Interface
3. APN
4. Protocol
MOBILE MODEM
LOCAL NETWORKS
The router might have glitches after running for days or weeks.
Reboot the router could solve most of the issues.
You may go to
System > Reboot
or unplug the PoE injector to reboot the router.
If the router works unstable after made changes to the firmware, please go to
System > Backup / Flash Firmware
. Click the
Perform reset
button to run a soft reset.
If unable to access the router admin panel, please run a hard reset.
When the device is powered on, tap and hold the
round
Reset
button
for 5 seconds.
Then release it and
wait for 4 minutes
to boot up.
! IMPORTANT !
DO NOT TURN OFF POWER WHILE RESETTING THE ROUTER!
Thanks for reading! If you have questions while using the router,
please check the online manual at
ezr33.outdoorrouter.com/v/33l
Please feel free to contact us if you need any further assistance.
RECOVERY
5. Debug
STEP
4.5
STEP
4.6
STEP
4.2
STEP
4.3
Router
password
Wi-Fi SSID
& password
Reboot
Soft
Reset
Hard
Reset
STEP
4.4
OutdoorRouter
www.outdoorrouter.com
Feel free to contact us if you need any further assistance.
Call Us
United Kingdom
United States
Australia
Send An E-Mail
+44 020 3575 1156
+1 323 521 4621
+61 02 8205 3116
Wenn Sie weitere Unterstützung benötigen, können Sie uns gerne kontaktieren.
WORKING PRINCIPLE
WIE FUNKTIONIERT EIN 4G-ROUTER?
Mobile
Internet
Cell
Tower
Wi-Fi & Ethernet
Secondary
Router
EZR33
Outdoor
4G Router
