Outdoor GreatRoom Company Lodge II Pergola Скачать руководство пользователя страница 2

Introduction 

Thank you for your purchase from The Outdoor GreatRoom Company.  This pergola has been engineered and manufactured in the USA.  

The purpose of this manual is to make the installation and assembly simpler.  Outdoor GreatRoom company recommends visiting with 

your local authority for building codes, restrictions, or requirements for this product.  Please read the manual through before starting 
the project.   

 
This pergola is made of  premium grade kiln dried Douglas Fir.  Douglas Fir, if maintained properly, will last a very long time, similar to 

life of both Cedar and Redwood.  All finished pieces have been dipped in stain to ensure penetration.  It is recommended that the 

pergola receive a clear, oil based stain yearly to maintain the color, minimize warping and prevent rotting.  Every few years a colored 
oil based stain should be used to keep the original color.  

Due to the immersion process used to stain wood pieces, parts may arrive slightly wet. If this occurs, it is recommended that wood 
pieces be removed from crate and allowed to air-dry for a day or two before assembly.   

 

Important:   
Anchoring Required—Contact your local authority for details 

Read instructions prior to assembly 
Assistance is required and we recommend at least 4 people for installation 

Do not let wood pergolas touch bare ground. Over time this can cause moisture damage and rotting of wood. 

If you have questions contact the place of purchase 

 

Douglas Fir Lumber may have surface splits.  This occurs while the lumber dries and seasons.  This characteristic is also known as 
“checking” in the lumber industry.  These can be upwards of 1/8” running inches to feet in length.  These characteristics do not deter 

the structural strength and integrity of the product nor does it affect or void the warranty. 

 

Before Beginning, make sure that all components listed on the next page were included with your hardware kit. Contact 

your dealer if any parts are missing.  

 

  Tools Required 

 

Corded or Cordless Drill 

 

Phillips screw bit 

 

Measuring Tape 

 

Level  

 

Socket Set 

 

Rubber Mallet 

 

Ladder  

 

Hammer Drill* 

 

Concrete Drill Bit* 

 

Concrete Anchors* 

 

Forklift (Highly recommended for raising sides and A-frame, but not required)  

 

Metal shears (required for optional roof installation) 

*Only Required for anchoring to concrete surfaces. 

 

Disclaimer—The Outdoor GreatRoom Company is not liable for damage caused by weather or misuse

  

 

Содержание Lodge II Pergola















Отзывы: